Search:

Type: Posts; User: moquinn

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    17,068

    The only issue I'm having with emulation at the...

    The only issue I'm having with emulation at the moment is switching the 10k (inner switch) after connecting to the AUP1. I have read a lot post on here that say to have the inner switch in the 10k...
  2. Replies
    6
    Views
    17,068

    It was going into limp home mode. The .xdf file I...

    It was going into limp home mode. The .xdf file I was using did not have a "Mask ID"parameter so I could not disable the checksum. I've had little time to work on the car but it runs pretty good now.
  3. Replies
    1
    Views
    3,167

    I'm just going to chalk that one up to being a...

    I'm just going to chalk that one up to being a newbie mistake. I had the "crank PW vs coolant temp" set too low. I thought just a little over the running PW would be enough to start the engine. After...
  4. Replies
    1
    Views
    3,167

    Cold start issues

    The car is a 1986 TPI Camaro with a 400 sbc. I'm using the ARAP bin with 6E XDF. I have tried adjusting the "Start-up enrichment vs coolant temp" table but the car will not start "cold". I've tried...
  5. Thread: limp mode

    by moquinn
    Replies
    0
    Views
    2,099

    limp mode

    OK guys this one has me stumped. I'm working with an ASDT bin file for a 1989 5.7 Camaro with a 1227165_6e xdf. Everything was going good, car was running pretty decent. Finally good enough I felt...
  6. Thread: timing issues

    by moquinn
    Replies
    0
    Views
    2,193

    timing issues

    I'm having problems setting the timing in Tuner Pro. I have a 1986 IROC that came with the 305 but swapped that with a 400. The computer is a 1227165, I'm using a AUM bin, $32 xdf and 1227165_160 adx...
  7. I have followed your directions and tried several...

    I have followed your directions and tried several times but can not get it to save. It will save everything but the equation. Any ideas why?
  8. Replies
    0
    Views
    1,663

    TPI BPW spiking

    While driving my BPW was spiking from around 4.7m/sec to 11 and once to 21.43 m/sec at the slightest acceleration. I was not doing any WOT pulls just light acceleration. The TPS was not going over...
  9. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    I am using Tuner Pro RT with the Moates Autoprom...

    I am using Tuner Pro RT with the Moates Autoprom for emulation. As of right now I have to enter 80F into the Prom ID scalar to make any changes during emulation. If the engine shuts down for any...
  10. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    The key was off. No power to the ecm when I...

    The key was off. No power to the ecm when I loaded the file. I will have to start from scratch tomorrow morning. Hopefully I can get this figured out because I cannot make any real-time changes as of...
  11. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    It would not let me change it while emulating. I...

    It would not let me change it while emulating. I had to "release hardware", change the mask id then re-upload the file to the auto prom. That's when it started.
  12. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    OK I still must not have something right. As soon...

    OK I still must not have something right. As soon as I tried to disable the checksum, as described on a different thread, my cooling fan came on and my data log info started reading crazy.
  13. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    Ahhh.... OK ,it was just named differently....

    Ahhh.... OK ,it was just named differently. thanks for your help
  14. Thread: No Mask ID?

    by moquinn
    Replies
    9
    Views
    7,104

    No Mask ID?

    I have read a post on here about setting the mask ID to AA for disabling the checksum. The current bin file I'm working with does not show a mask ID anywhere under scalars or tables. I have a 1227165...
  15. Replies
    5
    Views
    19,681

    1227165

    11573I have a 1986 Iroc with the 1227165 ecm. I have tried several times but cannot build a monitor that works. When I load the RPMs or coolant temp all I get is flat lines with no increments.
  16. Replies
    6
    Views
    17,068

    Tuner Pro RT and Moates Autoprom issues

    Hey guys any help would be appreciated. I'm new to tuning and cannot get my autoprom to emulate correctly. My car will run with the stock chip and memcal but if I use the autoprom with the G1 adapter...
  17. Replies
    2
    Views
    2,781

    I'm working on a 1986 iroc tpi. The car...

    I'm working on a 1986 iroc tpi. The car originally came with the 5.0 but I have pulled that out and put in a sb 400. The 400 is, as far as I know, completely stock. I'm wanting to keep the tpi. I'm...
  18. Replies
    2
    Views
    2,781

    Hi guys. I'm new to this forum.

    I'm new to tuning so please bare with me if I ask stupid questions.
Results 1 to 18 of 18