Search:

Type: Posts; User: muddyjimmy

Search: Search took 0.00 seconds.

  1. Thread: RPM Datalog

    by muddyjimmy
    Replies
    4
    Views
    5,929

    I understand a little of what you said but I...

    I understand a little of what you said but I would not know where to look to get that done. I wonder if anyone has done this before.
  2. Thread: RPM Datalog

    by muddyjimmy
    Replies
    4
    Views
    5,929

    RPM Datalog

    I have been datalogging my car at the track and have noticed that the highest RPM it logs is 6375. My car definitely has a higher rpm than that when running down the track. Is there a limit in...
  3. Replies
    15
    Views
    19,113

    I programed the settings in the Wideband and...

    I programed the settings in the Wideband and inserted conversion for 10-20 afr. Everything seems to be reading correctly and the laptop matches the gauge. Thanks again for everyone's help.
  4. Replies
    44
    Views
    34,273

    So I did the BLM locker and added 20% fuel to my...

    So I did the BLM locker and added 20% fuel to my WOT table and I made a couple runs on my way home tonight. They were all rolling WOT runs and the AFR stayed 12.7-12.8 all the way. I started with...
  5. Replies
    44
    Views
    34,273

    Thanks for the information on that. I am going...

    Thanks for the information on that. I am going to lock the BLM and add the 20% and tune from there with my wideband. My car is just a bolt-on LT1 so I would think that the fueling should be close...
  6. Replies
    44
    Views
    34,273

    I am going to try this on my tune but I did...

    I am going to try this on my tune but I did notice in my PE% Change To Fuel/Air Ratio @ WOT table the numbers go negative at 4000 RPM. Is this normal? If I multiply by 1.2 to get the 20% wont that...
  7. Replies
    15
    Views
    19,113

    Awesome information guys. This is what I am...

    Awesome information guys. This is what I am looking for. I will try it out in the next few days and let you know how it goes. Thanks again.
  8. Replies
    15
    Views
    19,113

    Ok thanks for the information. The Innovate...

    Ok thanks for the information. The Innovate MTX-L has the 0-5 volt output that I was going to use at 7.3 - 22.x AFR range
  9. Replies
    15
    Views
    19,113

    That is the conversion equation I need to make...

    That is the conversion equation I need to make the wideband read correctly in TunerPro? If I remember correctly, when poking around in the "edit ADX" file, I did see an area to insert a new...
  10. Replies
    15
    Views
    19,113

    That should not be a problem since the a/c is no...

    That should not be a problem since the a/c is no longer on the vehicle. How would I set it up so it will datalog AFR instead of psi? Is there a conversion in tunerpro that I can make?
  11. Replies
    15
    Views
    19,113

    The A/C wire is one that I left during my...

    The A/C wire is one that I left during my conversion but it would not be a problem to add the Oil Temp if that would be a better option. I do not know how to add the output or change the...
  12. Replies
    15
    Views
    19,113

    Wideband Question

    Hello all. I am in the process of tuning my 94 F-body LT1/4L60e that has been transplanted into an 85 Camaro. It seems to run great on the mail-order tune but I just have a feeling that I can get...
Results 1 to 12 of 12