Need to swap out injectors 2&3 and 4&7
also need to swap injectors 2&3 and 4&7
That being said, motor will not fire up if this was not done. I'm sure this is not your issue for the erratic vacuum....
Type: Posts; User: Mikey G
Need to swap out injectors 2&3 and 4&7
also need to swap injectors 2&3 and 4&7
That being said, motor will not fire up if this was not done. I'm sure this is not your issue for the erratic vacuum....
There are injectors and coil connections to swap out when going from LS to SBC
I have build three stand alone harnesses for others with no issues
Let me know
Mikey G
See attached schematic I found on the internet and used in my build.
Looking to see if you're firing on all cylinders with a temp gun is very useful - correct if required
Check your initial and total timing. Engine can sound quite good but have a low vacuum.
How are...
You set up is quite similar to mine. I have 10.5 with 6'' rods. I chose the AFR 195cc. CC Xtreme EFI 280 -m 230/236 with 109°. 1-5/8'' shorty headers with 2.5'' dual cats, mufflers and Morose...
I understand completely. Can you communicate your issues to the tune shop? If they have the ability to actually tune your application, they can confirm there is a hardware issue of just a software...
When I got started with this project, I put a carb on for simplicity as I knew there would be much troubleshooting elsewhere in the car. I really liked the TPI I had sitting on the shelf as well. I...
Interesting. My issue is with the right bank. We swapped the O2 sensors for other known working units and also the wiring from right to left to bank to confirm it was the wiring. We tested the right...
No I didn't.
Purchasing the software and credits was more expensive than having it tuned at my local shop. He had it done in 3 pulls I would still be fiddling with it today... They did load it...
https://www.youtube.com/watch?v=lqdPT1PGZUI
Hello Everyone.
Start-up done went well dyno day was Monday. RWHP was 330hp and RWT was 392ft/lbs
If the link did load
see Youtube - V8 RWD...
Hello All,
Small update. I finished buttoning things up last night. After fixing a pin out issue on the crank sensor it fired up immediately and idled quite well. as soon as the snow dissipates...
Hi Fast355,
Thanks for your responses - well appreciated.
What changes - if any, would you consider if you were using aluminum heads ? like AFR Street 65cc 195s....
Is your WBO2 wired to...
Hi Fast355 ...
Happy Holidays All. - Just a small update to my 24x conversion. I stripped out the OBDI harness and installed the OBDII (0411) today. The front of the engine has been stripped down to add in the 24x...
Very nice install dave w. Looks factory installed. Being bone stock, I'm sure dialing in your tune was not so difficult. I don't think I will have it that easy.
I don't currently have a WB02, but is on my list of things to do during the swap over to the 0411. I will certainly keep an eye on the cranking voltage drop. I was considering getting a local tuner...
I had intensions on getting my 0411 re-flashed with the F body (cable drive), and also having the VATS disabled prior to a start-up
I was actually going to go further and use the LS1 set-up with the Coil On Cyl. I have all the hardware. I have completed my harness as well. I was wondering if someone has had success with dialling...
Hello All,I built a 500hp 383 SBC and put it in a project. in the beginning, it was carburated for simplicity so I could have concentrated on debugging the car. Later I cleaned up the TPI set-up,...
How does one go about moving a tread from the introductions to a more appropriate area ?
See attached xdf and xdl files I currently have loaded into my TumerPro
Thanks Dave W,
As this is my first TunerPro tune, I have but to wonder if it is installed with all the correct files (?) When I get home, I will post what I have for your review,
Thanks
See attached log files from today
cs = cold start up
hi = hot idle
rt = road trip
Hope this helps
Hi Dave W,
I did not data record the last two start-ups or road trips. I will get you a fresh data log. See what time I get home tonight. Would you like more than just the cold start-up and hot...
Hello All,
My apologies for not updating sooner. I have installed the TPI and had it running since spring of 2015. With the exception of the idle, the car drives quite well. The idle is quite...