I think this is labelled knock retard incorrectly. It should be retard, and it can originate from high number of tables and conditions.

I guess in this case it pulls timing due to tcc or...

You can try this new program. It can tune your bin and it doesn`t need a xdf.

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?9616-New-LS1-Tuning-Tool-Universal-Patcher

How to turn...

Do you get injector pulse? First check the wiring per the diagram is correct. Than a way to log rpm and dtc from pcm while cranking.
Sensors should be labelled too. A B C for example.

You can use this file for reference or for a base. It is stock but not good for cloning. Eeprom area is scrambled. Cal only writing, or OS+cal suggested.

Set for 3.23 rear axle ratio. If the van...

With pcmhammer you can`t read/write that pcm yet. Lsdroid have some support for it but is still unreleased.

With tunerpro even you can find an xdf you can`t fix checksum of the bin, no plugins...

You can test this program. It supports most of the v6 bins and can also update the checksums, it uses tinytuner database. Xdfs for v6 are non existent. At least I haven`t seen one.
...

Great you managed to get it working. Did you make a note when the problem disappeared.

On the trans issue.

T/F is true/false. You noticed that right. It is a Boolean settings, so true means...

It is a joint project, with lots of people involved.

It will be great to test with that jet cable.

Can you check which version of program you are running. Just to rule out some of the unknowns.
Info for logging setup, bluetooth, usb, car year, pcm type, is there is more modules on bus or engine...

It looks like a bug. Can you share the exact steps you are doing[from opening the looger -till the point of error].

Just in case the sequence can be
settings->configure device->connect
profile...

You can try this new program. It can tune your bin and it doesn`t need a xdf.

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?9616-New-LS1-Tuning-Tool-Universal-Patcher

How to turn...

The jet looks as the newer usb design.

You can do some quick test with this program and test will it recognize it.
...

I was also thinking about some rpm modifier for eoit target, but refreshing that realtime will be useless. Since there is some scalars so eoit target don`t jump off like crazy but update slowly...

You can check here. Generate xdf for your OS or tune from the program. It can also do some basic datalogging if you have the needed device.
...

UPDATED first post with latest tableseek. Around 150+ more tables defined.

I will also point some of the less to guess features. It have been stated that universal patcher can open only single...

Moates roadrunner can do the trick. But you will be 2k+ off to get it started.

Any feedback will be greatly appreciated.

If for some reasons pcm reads less voltage than actual, I have some other versions that can be run. Reading voltage directly from injector circuit, on a...

For ls1 stuff and up there is one table MBT spark. That is the ideal spark for that engine under lab conditions.

Usually optimal spark depends on combustion chamber, compression ratio and cam...

3891 (FF) is 8 bit limitation, so that is the max you put for these cells. I guess they are in very unusual conditions so you don`t have to worry about it.

I suggest you apply the

low pulse...

You can apply the low pulse offset adder separately. When applied all tables for fueling comes from patch, so that is the only ones you need to adjust. I think I added some math conversions in the...

Updated first post with latest tableseek file. It have some maf erro parameters defined.
A full ve patch have been on the to do list but still no free time to finish.

Some other cool features...

I looked, but not defined yet for MAF fails frequency. It should be easy fix. Any other stuff you may find useful that is missing.

You can also skip the xdf part and edit the bin in Universal patcher.

Open the bin in tuner->file->open bin->switch to category view->3rd tab icon->scroll to Fan_Control category

Look for ...

You got that right.

Latest version have also some patches added.

-Lean cruise patch for all ls1 from 2001- on. 2 part patch. First LC cruise patch must be installed than the stock tables from a...

UPDATED first post with latest version
Version 0.20.18 uploaded