Search:

Type: Posts; User: Mark1978

Search: Search took 0.01 seconds.

  1. Anyone have lt1 closed throttle spark table?

    Does anyone have an lt1 closed throttle timing table?
  2. ok I drove it today and datalogged it. I think...

    ok I drove it today and datalogged it. I think this thing is lean all the way around. where would I start to add fuel across the board? I would think on a cold start warm up afr would want to stay...
  3. Dave check the open loop afr vs. temp vs vacuum...

    Dave check the open loop afr vs. temp vs vacuum table values, in the other bin vs this one. I just changed them in this bin. I'll burn the chip and try it in the morning. The original values seemed...
  4. ok I set the injector flow rate to 58 and I am...

    ok I set the injector flow rate to 58 and I am still way lean, also it hunts for idle. This was a cold start.
  5. MYSTERY SOLVED! I'm an idiot. On the burner 2 it...

    MYSTERY SOLVED! I'm an idiot. On the burner 2 it says "notch toward handle" so I've been installing the chips all the way to the top. While the lower part of the burner clearly says (in very small...
  6. ok question- when I put a chip into the burner 2...

    ok question- when I put a chip into the burner 2 and hit "erase chip" it says operation successful, but when I hit blank check it says chip is NOT blank. if I load a file and prog the chip, then hit...
  7. ok I just removed the chip adapter and installed...

    ok I just removed the chip adapter and installed the memcal. BOOM- connected. So I must have something in my settings in tunerpro wonky. When I uninstalled and re-installed the program it picked up...
  8. I’m using a Moates burner2

    I’m using a Moates burner2
  9. ok after many different approaches I need some...

    ok after many different approaches I need some help. In the first bin "dataworks" data logging works, in the second bin "no data" datalogging does not work. the first chip I burned one time. the...
  10. Well I have to use a track pad on a laptop to...

    Well I have to use a track pad on a laptop to slide the values. I tried clicking on the numbers to type a value but you have to slide the bar. Did you see any reason the datalog would not function?...
  11. I think I messed up something with the burn...

    I think I messed up something with the burn process. Maybe I accidently changed a setting or something. The chip that I was using to datalog works fine. So I copied it to a buffer and then burned it...
  12. OK now I have something weird going on. I tried...

    OK now I have something weird going on. I tried changing the injector flow and it brought the fuel trim where it needed to be but raised the idle. Also since I burned that chip (separate than the one...
  13. Dave, I am using an AEM 30-4110 with the 0-5v...

    Dave, I am using an AEM 30-4110 with the 0-5v output wired direct into the ecm per the screenshot. I also downloaded the spreadsheet file you created and open office to open it. But I cannot open the...
  14. so newbie it hurts. need some help with open loop

    ok here's the short version:
    94 k2500
    355 vortec flat top pistons
    gm performance cam
    bbc tbi red top injectors/ 97 vortec fuel pump
    I am running $OD and have the wideband wired up
    Now when I...
  15. Replies
    3
    Views
    15,251

    Ok I was able to score a 95 454 tbi with adapter...

    Ok I was able to score a 95 454 tbi with adapter for $150. What is the best way to clean the unit? Disassemble it and put the pieces in carb cleaning dip or clean it off with brake cleaner and bead...
  16. Replies
    3
    Views
    15,251

    Thanks, I'll see if I can find one

    Thanks, I'll see if I can find one
  17. Replies
    5
    Views
    17,715

    still got it?

    still got it?
  18. Replies
    3
    Views
    15,251

    FUEL SYSTEM ADVISE

    ok looking for some fuel system advice. I should have engine ready to drop in tomorrow. I have a 94 k2500 4x4 original 350 4l60.. im building a 97 vortec 355 flat top pistons,with a gm performance...
  19. Replies
    3
    Views
    17,959

    well I'm totally green with this form of...

    well I'm totally green with this form of tuning/ecm adjustment. I don't know what a mask is yet. I was meaning what ecm part numbers would work in my truck 94 k2500 4x4 4l60e? I think I may have...
  20. Replies
    3
    Views
    17,959

    ecm compatability chart?

    this many have been covered in another thread but I couldn't find it in the stickys. is there an ecm compatibility chart? my ecm is service no.16197427 bjlh the second sticker is 16198135
    thanks
  21. Replies
    5
    Views
    4,337

    Would it be worth calling jet chips or super...

    Would it be worth calling jet chips or super chips seeing if they can get some up and running or see if someone on the board has something? It’s just a daily driver. Nothing special. I had the vortec...
  22. Replies
    5
    Views
    4,337

    I know I need to upgrade the fuel system and I...

    I know I need to upgrade the fuel system and I see the chip burning software is free and the chip stuff is fairly cheap. How much work would be involved making a stock vortec engine run well?
  23. Replies
    5
    Views
    4,337

    Need some solid advice

    Hey guys I have a 94 k2500 4x4 it was a 350 tbi. The engine blew up and I am in the process of building a vortec engine. I’m dropping the stuff off at the machine shop Monday. This truck is just a...
  24. Replies
    0
    Views
    1,934

    Hi from Jacksonville Fl

    hello, I have a 94 k2500 I am in the process of building a vortec engine for it and I want to try and burn my own chip. Pretty cool site lots of great info.
  25. Thread: Tuning stuff

    by Mark1978
    Replies
    4
    Views
    5,436

    is this still available?

    is this still available?
Results 1 to 25 of 25