Uploading my latest idle tune. This one has a lot of changes for good reasons. Firstly I lowered the A/C idle because putting on the A/C did make the engine jump up a lot in idle, so I just made it...

Just updating that I finally got around to trying my Vette and did some changes to the idle. I raised the idle higher, especially when I have the A/C on since it really likes to die when that's on. ...

It's a Brian Tooley BTR Stage 2 with specs being 227/238 .620"/.605" 113.5LSA.

It's a ProTorque torque converter 3200 that I bought from tabbruzz from the Corvette forum. He's the reason that I...

That's one of the XDF's I've been using. I tend to switch between some, and even use Universal Patcher. I guess I turned on B4206? I don't remember doing that. Looking at previous bin's, it looks...

I haven't done anything to the Vette since as I've also been busy dealing with my other cars which need fixing. I did flash yet another change to the tune as I did increase the open loop table by...

This one? Is there a cheaper alternative? ...

I wanna make changes to my 07 Tahoe with a 5.3L but I need a cable that'll work with TunerPro and or Universal Patcher. Anyone got any recommendations? The cable I use for my 02 Vette doesn't seem...

I set it to stock then lowered everything by 20% and the car wouldn't run in park. Went back to stock and increased it by 15% which made it idle so much better. Still stalls if I put the car in...

I think I found it. I think it's called B3605 Open Loop Commanded Fuel. Should I just decrease everything by 20%? I have an original bin I found to compare and it does seem like the values were...

I did a quick startup at idle and logged it but it didn't report short term or long term trims until it warmed up a bit which took a few minutes. I then saw it report -22% and then slowly climbed up...

No wideband yet. I figure that's for next year when it isn't so cold. I do have the trans cooler but not installed for the same reason. I don't have a garage to park my car in. I never looked to...

Since I put a cam in my 02 Vette I can't get it to idle unless I let the car warm up. It'll idle just fine when I crank the engine, but it's when I shift into gear it just stalls. Once I warm it up...

If I cruise at 60 mph I was getting 22mpg if I'm lucky. Local roads it's far worse. I take these trips that's a good 6 hours total driving and it averages according to the car about 17.6mpg. It...

Been playing around with the car a lot trying to perfect mpg and idle. I can't say I've made great progress in both. With Chucks tune it took 15 minutes until I could shift the car into driver or...

I have a BTR Stage 2 cam installed on my 02 Corvette and wanted to see how other people tuned their cars with this cam. The specs are 227/238 .620"/.605" 113.5LSA. I uploaded my current tune for...

Flashed it with the patch I found and it isn't as good as before. It definitely goes into lean cruise and you can barely hear the engine when it happens which is around 47 Mph. As far as mpg, yea...

I found it here. It's what I've been using to make the MAF changes to turn off VE.

I have cats and was told that was a dumb idea. Don't wanna fail inspection. Never know if they start using...

I think it is on but there's another lean cruise? I think it has to do with the XDF I found on pcmhacking.net, which I still haven't been able to register. Haven't gotten an email to activate and...

Tried the bin you edited and it seems to work. Giving gas now breaks traction, and fairly easily too. Also once I get to 30+Mph I can get close to 30 Mpg. I haven't taken it on the highway because...

Thanks, I'll give it a try tomorrow. I'm thinking that maybe Chuck turned off Power Enrichment since he just let the engine run rich 24/7?

That's a good idea.

Now that you mention Power enrichment, that was one of the settings the YouTube video had me change to disable VE by setting PE Normal Mode Enable to 90. Wasn't sure if I...

I made more changes to the maf and turned back on the VE table, at least I think I did, and flashed it to the car. The performance isn't as good as it was with Chuck's tune. Maybe it's my...

It's one of the things I wanna do before the final flash I do. I did look at it but not sure how it's suppose to help? There is mention of 2nd gear and TCC but that's mostly for towing. Couldn't I...

Did what you explained and it certainly got better. I might have logged a bit better but I think one more adjustment and it should fine. I assume that once that's done I undo the changes the guy...

I think I get it. So I made the layout and used the Frequency for the MAF instead of the pressure and this is what I got. Going by this I assume I need to add? Looking at the log I don't see my...