Prog ID BCC Size Year Release Date Eprom ECM Prom ID Scan ID Platform Engine Disp. Trans Trans Type Gear Ratio
BBMD 1993 33702 16179257 16168625 9258 9291 C1 L05 5.7 M30 AUTO GT4
Type: Posts; User: In-Tech
Prog ID BCC Size Year Release Date Eprom ECM Prom ID Scan ID Platform Engine Disp. Trans Trans Type Gear Ratio
BBMD 1993 33702 16179257 16168625 9258 9291 C1 L05 5.7 M30 AUTO GT4
Thanks Tom,
I mentioned PM in case you didn't want if public. Man, shit ton of equates in there :happy: I'll have a gander tomorrow :)
Hiya Tom, I will have to dig to find this older stuff. I'm surprised you are using MotS, Intel hex has always seemed good but I have never worked with your box. If you would like, PM me the code to...
Very common smog problem with ANTY.
Double check chip orientation. Dimple in chip needs to match dimple in holder.
Hi Tom,
Yeah, I was having a little fun about the substrate :) This situation has no worries, it just reminded me when I wrote a "burner" to test. The spec sheet said it was only good for ~100,000...
Hahaha, chanting :laugh:
Back in the 90's I ran some tests on some TMS370 stuff, brutally burning the bit flips from 00h-FFh and it took ~30,000,000 cycles before partial failure. Adding that short...
I'll say a small prayer for the substrate. :laugh: :happy:
Hiya,
I'll take them if willing. Shipping to 93710 USPS priority preferred.
Hiya Tom,
At a glance, the SLOOP is an incredibly tight loop especially in eeprom and not flash.
In my mind, if you have room, I am thinking a JSR to use some ticks as well as more ticks using the...
Thanks guys, front page updated :)
Hiya's
Does anyone have a new code?
P.S. Found on the interweb
255076685227989677
Hiya,
You're missing the point. We used vortec pumps(58psi) to replace the tbi pumps all the time, the regulator is what controls the pressure, not the pump. A 60psi CAPABLE pump will still make...
Hiya's
The "adaptives" basically don't work in these early computers. I wouldn't set anything under .25 in those fields either way. Adjust everything in the pressure tablles and/or in the force...
:welcome2:
Hiya,
Does this have stock injectors or aftermarket replacements? I've only seen this happen with aftermarket and high fuel pressure as they are then slow to respond. That big manifold and spacer...
Good call steveo :)
^^^^^ This!
Just moving an old harness can "break" it :( So many hot/cold cycles and it will live a very long time, till it moves.
Hiya,
I don't know if it matters in this mask. I have always found most GM stuff requires the tps voltage to be between .5-.6v for idle control to work correctly. Most times with big cams that...
Hiya,
Interesting how I cannot read the source file. I can already beat up ANY e38, your files are suspect, hate to say if you are actually contributing.
:welcome2:
Wow, good data.
Thanks Dave :)
Thanks given to MO LS for sharing, credit given in OP, it's nice to see this thread grow, thanks to sledhead2 too :)
Ok, cool
Sounds like you have a grasp on the struggles ahead :)
If iirc a fmu is about 1.25:1
Your real struggle will be to find large enough injectors for the TBI. There was a time I had to use BBC 75's @ 12lb injectors and then use a 3:1 regulator. Figure...
Hello,
A "boost-a-pump" increases the flow, the pressure has to rise at least 1:1 vs. Meaning if base pressure is 12, at 10 lbs boost the fuel pressure needs to be 22 to maintain the flow. Any...