Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: Six_Shooter

Page 1 of 4 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    24
    Views
    548

    Ignore the hardware not found error, that's for...

    Ignore the hardware not found error, that's for emulation devices, like the Ostrich 2.0 and AutoProm.

    You need to go into preferences and set everything for the cable in there.

    Yes, you need to...
  2. Replies
    24
    Views
    548

    I have an Ostrich or 2 I'm thinking about parting...

    I have an Ostrich or 2 I'm thinking about parting with. I have several, and don't use OBD1 GM ECMs on as many of my vehicles anymore, most have or will have Megasquirt, one will stick with the GM...
  3. Replies
    24
    Views
    548

    I have found one of the best tools to use for...

    I have found one of the best tools to use for someone to understand the changes made to a tune/BIN is to use an EPROM emulator, like an Ostrich 2.0 or AutoProm, which it sounds like you didn't buy.
    ...
  4. Yes, you still need to program the EEPROM with...

    Yes, you still need to program the EEPROM with the proper offsets, then the hardware offset (shorted pins) allows everything to work together.
  5. Replies
    15
    Views
    694

    Sounds right about connecting the VSS. Where...

    Sounds right about connecting the VSS.

    Where are you located, there are members all over and one might be local to help you out with your PROM.
  6. Replies
    15
    Views
    694

    VSS, is required on all GM OBD1 ECMs for best...

    VSS, is required on all GM OBD1 ECMs for best results. The VSS is used by the ECM to control engine states (idle, accel, cruise, etc) and makes tuning under all conditions much easier and just...
  7. I have a thought about this... Have you...

    I have a thought about this...

    Have you verified timing to be correct? That what is being commanded is what is actually happening referencing crank angle, at RPM, I know without a dyno under load...
  8. Replies
    30
    Views
    3,875

    Did you mean 16197427? That would be an OBD1...

    Did you mean 16197427?

    That would be an OBD1 PCM and would be what I would use over the 7747. It has MUCH faster coms for better datalogging, more tuneability, and just a better overall ECM IMO.
  9. That "special" filter is the same one used on...

    That "special" filter is the same one used on every other fuel only Howell setup, in that it just triggers the ECM as the pulses come into it. Basically just takes the coil negative signal and...
  10. I got the same thing, I was just about to send a...

    I got the same thing, I was just about to send a PM to 1project2many, but since you started this thread, I'll just add on here...
  11. Replies
    5
    Views
    411

    Have you made sure that the distributer is...

    Have you made sure that the distributer is stabbed correctly? It sounds like it might be installed in the wrong position.
  12. TBI injectors are VERY easy to modify for...

    TBI injectors are VERY easy to modify for increased flow. The top has a threaded stud that is usually staked or tack welded and if you grind the stake or weld off, you can twist the stud and change...
  13. Thread: memcal

    by Six_Shooter
    Replies
    9
    Views
    712

    Yes, and sorta. It can be read, and programmed...

    Yes, and sorta.

    It can be read, and programmed to a different MEMCAL, however, the LHM (Limp Home Mode) and hardware fueling side along with the knock filter will not be correct and will throw a...
  14. Replies
    4
    Views
    632

    You can connect the laptop any time.

    You can connect the laptop any time.
  15. Replies
    4
    Views
    632

    As Dave said Tuner Pro, or a scanner can see...

    As Dave said Tuner Pro, or a scanner can see codes while the engine is running. Even better to datalog a session or three and see what was happening just previous to the code(s) being set.
  16. Replies
    11
    Views
    1,440

    He is, I've met with Alan a couple times now.

    He is, I've met with Alan a couple times now.
  17. Replies
    11
    Views
    1,440

    Lots of good info above, and I'll be definitely...

    Lots of good info above, and I'll be definitely looking into that Arduino sheild, since I enjoy coding and using Arduinos (most of the time lol).

    I do use 14point7 products a lot, they seem to be...
  18. Replies
    4
    Views
    1,089

    I believe there are also pinout diagrams in the...

    I believe there are also pinout diagrams in the fileman section as well.
  19. Thread: Stock PCM

    by Six_Shooter
    Replies
    4
    Views
    1,089

    Doesn't Holley have a trans controller, that will...

    Doesn't Holley have a trans controller, that will link to the Sniper? I think I'd do that, so that the ECU and the TCU can communicate with each other and not need extra sensors.

    You do have a...
  20. The macro fix is only for the data logging side,...

    The macro fix is only for the data logging side, it should have no effect on the emulation side.

    Another thing you can try is uploading the entire bin when change things instead of each individual...
  21. Emulation is not inherently glitchy, once...

    Emulation is not inherently glitchy, once everything is set correctly.

    The biggest thing you have to do is disable checksum, by changing the MASK ID in the bin to AA. This goes for all OBD1 GM...
  22. Replies
    25
    Views
    3,118

    The picture looks fine on my PC. *shrug* I...

    The picture looks fine on my PC. *shrug*

    I don't recall the exact dimensions of the notches, but it was basically made to be very close in size to the original crank wheel, to avoid any errors in...
  23. Replies
    25
    Views
    3,118

    This is what I did on my 1985 Jimmy originally,...

    This is what I did on my 1985 Jimmy originally, then the wheel was transferred to my Nissan L28 (I used GM EMS and DIS on it) and then onto my LX9, where it is currently.

    I did modify the sensor...
  24. Replies
    7
    Views
    2,679

    I have PM'd you.

    I have PM'd you.
  25. Replies
    7
    Views
    2,679

    Crossfire EPROM

    Crossfire EPROM
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4