Search:

Type: Posts; User: ralmo94

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    103
    Views
    2,047

    As far as I can tell it's for a 350 manual trans...

    As far as I can tell it's for a 350 manual trans and the right mask, I don't see why it wouldn't work.
    :rockon:
  2. Replies
    103
    Views
    2,047

    If it smells rich out of the pipe and the O2 is...

    If it smells rich out of the pipe and the O2 is saying it's too rich, I'd say there is a rich condition, and replacing the O2 is kinda like shooting the messenger.

    That's why I suggested...
  3. Replies
    103
    Views
    2,047

    As far as I know everything is in the bin for it,...

    As far as I know everything is in the bin for it, just have to add pins to the PCM connector and install one if wanted. Some have, and it is said to be better with a MAT rather than IAT as it's a...
  4. Replies
    103
    Views
    2,047

    As far as I know, your ECU will read any prom...

    As far as I know, your ECU will read any prom with the same mask, I had been told previously that the releases of new BCC codes were incremental meaning Ab superspeeds AA. But I have also been told...
  5. Replies
    103
    Views
    2,047

    TBI does not have IAT, or MAT. It uses engine...

    TBI does not have IAT, or MAT. It uses engine coolant temp.
  6. Replies
    7
    Views
    165

    Good to hear. Hope it continues to work as...

    Good to hear. Hope it continues to work as smoothly as reported now. :happy::rockon:
  7. Replies
    103
    Views
    2,047

    Certainly not to much to ask for. Lol. Yes you...

    Certainly not to much to ask for. Lol.
    Yes you can swap a 7427 if you would like, you would need a PCM, the two connectors and a memcal, and a chip to burn, I don't recommend using a memcal adapter...
  8. Replies
    103
    Views
    2,047

    I would check fuel pressure. They make a special...

    I would check fuel pressure. They make a special gauge for TBI that goes between the return line and the TBI.
  9. Replies
    103
    Views
    2,047

    Does he have any codes? It appears it has been...

    Does he have any codes?

    It appears it has been trying to lean the mixture to the extent it's allowed with a 111 BLM or long term, and it's open loop, short term is 128, 128 - no adjustment. ...
  10. Replies
    103
    Views
    2,047

    The more data is from the 7427 PCM, or equivalent...

    The more data is from the 7427 PCM, or equivalent service number.

    I personally am wondering about the prom, if it's stock, or uncorrupted. Optimal thing would be if you had another prom to...
  11. Replies
    2
    Views
    66

    Nice F body

    Nice F body
  12. Replies
    2
    Views
    66

    If you haven't already, you should check out...

    If you haven't already, you should check out steavo's site
    Ecmhack.com

    He is a member on here who has created free to use tools for that platform
  13. Replies
    9
    Views
    134

    Yes the starter wire should definitely not be hot...

    Yes the starter wire should definitely not be hot all the time, if you find it, I'll bet you also find the source of the arc. Hope it's an easy fix for you.
  14. Replies
    9
    Views
    238

    This might help with the cylinder select...

    This might help with the cylinder select knowledge.
    http://www.gearhead-efi.com/Fuel-Injection/showthread.php?454-What-If-8D-(1227727-ECM)-for-TBI&p=3374&viewfull=1#post3374

    Also, when you use...
  15. Replies
    9
    Views
    134

    So the starter wire is hot all the time? I would...

    So the starter wire is hot all the time? I would suspect a faulty ignition switch. Unless its hot after the relay, then I would suspect a sticky relay, they do stick sometimes.

    Then of course...
  16. Replies
    11
    Views
    203

    Nice looking jeep, and nice canoe's. While...

    Nice looking jeep, and nice canoe's.

    While port would be an advancement, I see no real world advantage over TBI, as long as it suits your rpm and cfm requirements, but a modded Clifford intake...
  17. Replies
    103
    Views
    2,047

    Glad to hear. Too many repairable trucks end up...

    Glad to hear. Too many repairable trucks end up in the scrap yard and are replaced with new trucks that aren't made as good. Well that's my opinion.
  18. Replies
    9
    Views
    134

    Was the truck operation before the swap? If so,...

    Was the truck operation before the swap?
    If so, was the purple wire going to the starter?
    Iirc in 93, the wire went right from the ignition switch to the starter solenoid without the fuse box
  19. Replies
    9
    Views
    134

    Hope it works for you, if not, you may need to...

    Hope it works for you, if not, you may need to verify your wiring :popcorn:
  20. Replies
    7
    Views
    165

    :popcorn:

    :popcorn:
  21. Replies
    103
    Views
    2,047

    Just looked at your first picture of the scanner...

    Just looked at your first picture of the scanner again, I noticed that the pnp or park neutral position is showing reverse
    Does this always show this, does it change when you push the clutch in ?
  22. Replies
    7
    Views
    165

    That's what I was thinking too, with each bank...

    That's what I was thinking too, with each bank firing it sort of mimics what a 2 barrel TBI would do.

    You could wire it the way you have proposed and report back to us if you have a TPI to play...
  23. Replies
    9
    Views
    134

    Just off the top of my head, vats, shouldn't keep...

    Just off the top of my head, vats, shouldn't keep you from cranking, just prevent firing up?
    Maybe some can correct me if I'm wrong on that.

    It sounds to me like something isn't wired correctly,...
  24. Replies
    103
    Views
    2,047

    Pretty much just a repin of the harness,...

    Pretty much just a repin of the harness, shouldn't be too bad should you decide to go that way.

    It's a more modern PCM than the ECU you have now, not sure, but should have a faster clock speed,...
  25. Replies
    103
    Views
    2,047

    31% is too much. Should be 0 with 0vlts I'm still...

    31% is too much. Should be 0 with 0vlts I'm still thinking maybe it's a glitch with your scanner. I guess we'll find out after you get your Cable.

    Could always do a 7427 swap. Lol
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4