"The transmission controller sounds awesome. Simple with full control. Keep up the good work. How much does it cost?"
Retail on the units including the controller, universal harness, remote TPS or...
Type: Posts; User: buddrow
"The transmission controller sounds awesome. Simple with full control. Keep up the good work. How much does it cost?"
Retail on the units including the controller, universal harness, remote TPS or...
Website has had a dimestore makeover, nothing earth-shattering though mostly appearance wise. Moved everything to it's own page and will continually make changes and updates to improve user...
Yes, the site is "up". It's lacking a lot but it, along with everything else is a work-in-progress. The official website is here - http://www.bspt.tech/home.html . Don't laugh as I just used the...
34blazer, are you still looking for a replacement for the JTEC? I'm looking into the dodge stuff now days and could use a tester if you're interested just pm me.
"Any suggestions on what arduino...
I already have an .adx for it, havent worked out the xdf yet. The software is meant to be easy to use so there isnt much of a learning curve such as you would have with TP. As far as veiwing and...
I realized it's been a while since I've posted an update so here goes.
The 4L60E/4L80E transmission controller is ready for the road. I have also been working on an alternative to TunerPro. Even...
No offense, but I am not really interested in sharing the code Ive spent the last year developing at the moment.
the only real component i am working on lining out is the pressure control system....
Alex,
Yes it is still in development. Still have in vehicle testing to be done and calibration software to write. I am lookong to have it interfaced with Tunerpro for tuning but as of now it...
34blazer and to whom it may concern,
Progress has been hit and miss. I still have some testing to do and software to update on both the 4l60e and the 4l80e. If you are interested in beta testing ...
Alex aka HotRodCadillac,
Dig the name and the project. Glad to hear you "stumbled" across my thread. I was never really happy with the aftermarket units as a whole. They work but, much like the...
34blazer,
Still working on it. I will tell you that for now, the source code will not be available but support will be.
What year is the transmission you plan on using this with? I can help...
If you can give me the year, make, model of Jag I will look and see what its connected to. Otherwise, stay tuned for further developments on my controller.
Buddrow
journeyman, As Robert suggested in the thread you started, looking into the data stream will provide some much needed info. Need to look and see if 4th gear is commanded by the pcm, and if not, why?...
UPDATE:
So, I'm trying to nail down any final additions before "finishing" the software for the controller. As it stands, I have implemented the following user information...
Streaming sensor...
Oh, it happened all right. :innocent2:
Pictures you say...:)
Hello Everyone!
Well it's been months since I have posted much about the trans controller and Ive been hard at work on it. Recently I have been putting together the ADX file to use with TunerPro...
Currently is does not control that trans but it can. It "can" operate numerous transmissions from GM, Ford and Chrysler and if there is a demand I will be happy to accommodate requests. Now, with...
Well Steveo, you would be proud of me. I banged away at TunerPro and the tcm board until I got serial comms working and a single element(TPS Volt) dash working last night about the time my eyes...
Skully,
Progress had slowed slightly. It's not quite ready for prime time just yet. If you wanted a barebones absolute minimum setup it would fit the bill but this thing has grown into a bit of a...
Just dropping an update, or a non-update at this point. Not much has progressed due to work and home life. Looking to have some free time this month(June) so hopefully I can get this thing on the...
Yes and no. Life has been a big interruption as of late so I havent had much time to work on it. How close are you to needing one?
Buddrow
rusefi,
I am on the fence currently as to how I will put this project to market, be it an open source item or commercial product. We can talk about your plans and take it from there. I am...
Rodeo,
I am in the process of bench testing right now. A month or so will hopefully give me enough time to get all(or most) the bugs worked out by the time you're ready.
I'll get you what Im working on in the next day or two.
Buddrow