Search:

Type: Posts; User: NISANDA

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 47 minute(s) ago.

  1. looks pretty good :thumbsup:

    looks pretty good :thumbsup:
  2. Replies
    7
    Views
    15,657

    i think its the same as Hptuner, to the info and...

    i think its the same as Hptuner, to the info and Vin of the computer, soo if you change Vin you need to license new vin, also you can read same as HPtuner but can write unless you license, So in...
  3. i have same problem, gets even worst with new...

    i have same problem, gets even worst with new car\truck .Cal files.
  4. Wow, didnt know this combination existed, the...

    Wow, didnt know this combination existed, the file shows its a manual vehicle also (L31 5.7 vortec)
  5. Are you tapping on the temp sensor for other...

    Are you tapping on the temp sensor for other gauges etc?.
  6. Replies
    3
    Views
    3,034

    not normal, but check you fuel pressure first.

    not normal, but check you fuel pressure first.
  7. Replies
    8
    Views
    19,365

    The Maf sensor has the IAT (Air temperature...

    The Maf sensor has the IAT (Air temperature sensor) integrated inside, if you run a mafless system its a good idea to buy a IAT sensor and run it somewhere for inlet air temp mesuarment.

    Just grab...
  8. Replies
    8
    Views
    19,365

    you can run with map only just unplug the maf and...

    you can run with map only just unplug the maf and adjust the low octane tables cuz high octane aren't available without the custom OS, run the IAT separate and your good to go.
  9. Replies
    132
    Views
    209,925

    this is great! news

    this is great! news
  10. Replies
    1
    Views
    17,514

    You need the HP scanner for that, tunercat/jet...

    You need the HP scanner for that, tunercat/jet doesn't even have one.
  11. Have one but its in Cal. file.

    Have one but its in Cal. file.
  12. Replies
    1
    Views
    22,006

    This is the Bench harness i use to read ALL 99 to...

    This is the Bench harness i use to read ALL 99 to 06 PCMs (Gen 3), 4Cil (ecotec Blue/clear), V6 (Blue/clear) and all V8 (Blue/Red, Blue/Green).

    Connector one PCM C1 BLUE
    PIN#19 Power Ignition...
  13. Replies
    23
    Views
    35,985

    I'm curious on how you plan to write the file?...

    I'm curious on how you plan to write the file? what are you using to tune? and the 411 pcm that you have its from what? sounds like you asking for the complete work not just a base file for your...
  14. Replies
    23
    Views
    35,985

    Assuming the motor its a LM7 gen3, because if its...

    Assuming the motor its a LM7 gen3, because if its Gen4 2007 its would be a LY5, and your swapping so the best you can do to get a correct file its provide the injectors part number, to at least have...
  15. Replies
    4
    Views
    13,818

    Just disable all the transmission DTCs, it will...

    Just disable all the transmission DTCs, it will run fine with you mechanical transmission and current motor.
  16. Have a cal file if you can work with it.

    Have a cal file if you can work with it.
  17. Replies
    6
    Views
    17,114

    Are all those files E67 controller only?, if yes...

    Are all those files E67 controller only?, if yes how to know what Serv. No.?
  18. Replies
    11
    Views
    19,187

    try this one, i made some changes maybe it will...

    try this one, i made some changes maybe it will start better also did a few tweaks for performance, still you need to tune for those injectors cuz 24lbs 3bar at 4 bar are more like 28lbs inj etc.
  19. Replies
    17
    Views
    30,798

    i run kind of the same setup for bench...

    i run kind of the same setup for bench read-writte, but only have check eng light, the obd2 port and the switch as led build in (ON on the ON position).
  20. Replies
    4
    Views
    13,350

    Great Info. Thanks for Sharing

    Great Info.

    Thanks for Sharing
  21. Replies
    17
    Views
    30,798

    Yes pretty much the same 

    Yes pretty much the same 
  22. Replies
    17
    Views
    30,798

    Yes, the pins are: Pin...

    Yes, the pins are:
    Pin 31 - Ign Voltage (Switch)
    Pin 32 - Battery Voltage (Constant)
    Pin 49 - Ground (Big Black-white wire)...
  23. Replies
    17
    Views
    30,798

    i can read t42 with out the e38 ECM they just...

    i can read t42 with out the e38 ECM they just dont show any vin number or vehicle info etc, but the file its readeble and writteable.
  24. Thread: 4L60 to 4L80

    by NISANDA
    Replies
    4
    Views
    16,446

    Grab any file with 4l80e and use import modules...

    Grab any file with 4l80e and use import modules option or segment swap (depending on software you are using) to tranfer the transmision part to your file.
  25. Just disconect the Maf and its should...

    Just disconect the Maf and its should automatically start using the Map.
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4