Search:

Type: Posts; User: Pulse_GTO

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: HELP PLEASE

    by Pulse_GTO
    Replies
    4
    Views
    1,619

    https://pcmhacking.net/forums/viewtopic.php?f=42&t...

    https://pcmhacking.net/forums/viewtopic.php?f=42&t=7946
  2. You will need the correct Blue Green harness with...

    You will need the correct Blue Green harness with the TPS and IAC connectors. I would probably use a 12587603 OS that has a 4L80E transmission segment. You can go into the options matrix and change...
  3. Replies
    3
    Views
    3,931

    Also check out www.efidynotuning.com...

    Also check out www.efidynotuning.com.
  4. Replies
    2
    Views
    2,386

    Also http://www.efidynotuning.com has some good...

    Also http://www.efidynotuning.com has some good information.
  5. Replies
    1
    Views
    674

    You can set the MIL to "No error reported" for...

    You can set the MIL to "No error reported" for the codes that do not apply to your application. I would still keep the codes that could help you diagnose something down the line, even if you don't...
  6. Replies
    12
    Views
    1,761

    I can't remember if when deleting VATS does the...

    I can't remember if when deleting VATS does the PCM need to be flashed calibration only or entire. Also does it need to be still powered for 30ish seconds after the flash to take the calibration? I...
  7. If you don't have a wideband you will need closed...

    If you don't have a wideband you will need closed loop activated in order to get feedback from the factory narrowband O2 sensors so that they may calculate the fuel trims. If you have a wideband...
  8. What software are you using to log the computer?

    What software are you using to log the computer?
  9. Replies
    8
    Views
    1,602

    Search "2005 GTO 4L80E conversion" and "E40 4L80E...

    Search "2005 GTO 4L80E conversion" and "E40 4L80E swap" on Google. There are some discussions about this.
  10. Replies
    9
    Views
    7,584

    Here is another version of the xdf:...

    Here is another version of the xdf: https://pcmhacking.net/forums/viewtopic.php?f=42&t=7916
  11. Any plans to expand into Ford EEC-IV products?

    Any plans to expand into Ford EEC-IV products?
  12. Replies
    13
    Views
    2,574

    No need to donate any money to me, I do it so...

    No need to donate any money to me, I do it so that people don't get taken to the cleaners by the big guys.

    Glad you figured out your issue!
  13. Replies
    5
    Views
    1,187

    What OS was originally in your PCM? Is DBW or...

    What OS was originally in your PCM? Is DBW or DBC?
  14. Thread: INTRO

    by Pulse_GTO
    Replies
    1
    Views
    518

    When you download the bin file from your PCM you...

    When you download the bin file from your PCM you will be able to see what OS it is. Then search for the matching XDF and you should be off to a good start.
  15. Replies
    2
    Views
    1,213

    2001 Corvettes used a drive by wire throttle...

    2001 Corvettes used a drive by wire throttle body, so if you still have the Corvette OS in the PCM you will have some problems using a drive by cable throttle body. I would probably use an OS from a...
  16. Replies
    11
    Views
    2,403

    I am Phoenix on the other forum, name was already...

    I am Phoenix on the other forum, name was already taken here, so I adapted.

    I actually did already have a 12606960 XDF done, just never got around to sharing it, I'm attaching it here. Just...
  17. I went ahead and define all the Fan tables for...

    I went ahead and define all the Fan tables for the 7603, can be found under Vehicle Settings>Fans in the attached XDF. Hopefully this helps.
  18. Replies
    8
    Views
    1,206

    Have you adjusted your injector data to reflect a...

    Have you adjusted your injector data to reflect a return style system at 43psi? Depending on what 5.3 file you are using, the injector data could be for return or returnless, but in either case the...
  19. Replies
    4
    Views
    1,340

    The ECU receives signal from the sender that is...

    The ECU receives signal from the sender that is screwed into the driver's side cylinder head. This signal will not work with aftermarket or factory dash gauges.
    Some people have used the 1998 LS1...
  20. Replies
    3
    Views
    1,666

    It appears to be under Transmission...

    It appears to be under Transmission Calibration>General>Four Wheel Drive Available. I'm al attaching the bin file linked above and the matching XDF.
  21. Did you disable the column lock option G0801?

    Did you disable the column lock option G0801?
  22. Replies
    2
    Views
    1,403

    I'm attaching a file that started as a...

    I'm attaching a file that started as a combination of a 2004 5.3 truck with manual transmission and a 2004 4.8 Express van with DBC. I swapped the engine calibration and engine diagnostics segments...
  23. Replies
    4
    Views
    1,395

    What OS are you using? IS this a swap? ...

    What OS are you using? IS this a swap? Typically I would go into the system options matrix and in the line or column that matches the vehicle platform selected in the bin and change ETC from 1 to...
  24. Flash it to your PCM then read it with a...

    Flash it to your PCM then read it with a different program.
  25. Usually the lower the number the less it hangs. ...

    Usually the lower the number the less it hangs. Also timing g too high can cause it to hang. It's a trial and error deal. Make sure your fueling is correct or you wind up chasing your tail.

    Did...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4