Search:

Type: Posts; User: WASyL

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    2,474

    it os compatible PCM, it is all about flash...

    it os compatible PCM, it is all about flash whether it will use some signals or not.

    best regards
  2. Replies
    8
    Views
    1,431

    If You won't hit stall wall then nothing to be...

    If You won't hit stall wall then nothing to be changed with torque converter swap.
  3. Replies
    0
    Views
    689

    Cruise control on E38 PCM

    I have swapped 8HP70 Jaguar transmission to 2011 Yukon RWD truck. PCM was reprogrammed to manual transmission so that BCM and PCM would control starter relay properly. Now my issue is that cruise...
  4. Replies
    6
    Views
    1,275

    Innovate is most problematic one, I prefer AEM...

    Innovate is most problematic one, I prefer AEM (but it is with gauge or 14point7.
  5. Replies
    1
    Views
    958

    Moates Extreme ALDL

    i'm looking for drivers/installer file for Moates Extreme ALDL cable, their website is down and can't find them on internet, can someone sher version that works on Windows 10 ?

    best regards
  6. Send me an email to cwbiuro@gmail.com asking for...

    Send me an email to cwbiuro@gmail.com asking for tune and I'll send You my one, it is '95 SD Tune using WBo2 for lean cruise and 13.1:1 WOT, auto trans with 3200 stall converter.
  7. Replies
    4
    Views
    885

    thanks

    thanks
  8. Replies
    4
    Views
    885

    no stretched timing chain, just installed new...

    no stretched timing chain, just installed new one, opti is new too, just these chinesse opti's that customer bought come so inaccurate, 96-97 PCM treats -10 to +7 as not to request MIL but i dont...
  9. Replies
    4
    Views
    885

    LT1 distibutor CKP Lo res angle question

    I just swapped PCM from 96-97 to 94-95. Thru 96-97 PCM i have checked that CKP: Lo Res Angle is -9 deg (new timing chain set and distributor), so now on 94-95 should i advance or retard whole...
  10. Thread: MAF spreadsheet

    by WASyL
    Replies
    23
    Views
    8,322

    as MAF tuning is new to me (im SD guy) i have...

    as MAF tuning is new to me (im SD guy) i have question how to use log.

    Lets say AFGS 46-50 and 51-55 log shows +7%, does that mean i need to multiply theres g/s valuses in tune file by 1.07 ? and...
  11. Replies
    4
    Views
    865

    Try Open Loop and see if this behavior continous

    Try Open Loop and see if this behavior continous
  12. Replies
    3
    Views
    770

    Thank you for the explanation :-) Best regards

    Thank you for the explanation :-)

    Best regards
  13. Replies
    3
    Views
    770

    MAF Tuning theoretical knowledge question

    I wonder why does MAF cars need to be tuned? Is there something I don't know or understand? As example let's take GM TPI MAF car.
    MAF (mass airflow sensor) reads current airflow very very accurately...
  14. That means - if every other stuff is ok - that...

    That means - if every other stuff is ok - that there was issue with flashing.
  15. Replies
    170
    Views
    183,525

    still working on that nitrous thru EGR control. ...

    still working on that nitrous thru EGR control. I don't know how gm/sec value is calculated so is it possible to do patch that does this:

    table "26c2 MIN EGR DC% vs airflow" change load value...
  16. Replies
    1
    Views
    619

    Oil and/or fuel pressure resistance table

    Does any of GM ecm/pcm has resistance or voltage table for fuel/oil pressure? I want to make pressure safety switch and need calibration for known (and cheap) sensor.
  17. Replies
    44
    Views
    6,097

    awsome tool, comes handy when doing lots of...

    awsome tool, comes handy when doing lots of tuning with different ECM/PCM but similar engine setups.
  18. Replies
    8
    Views
    2,357

    nice work, but if you know how to weld why not...

    nice work, but if you know how to weld why not open up that intake manifold to breath more air ?
  19. Replies
    3
    Views
    908

    Test that is the one. The other one is just for...

    Test that is the one. The other one is just for reading codes thru some basic applications not for flashing pcm
  20. Replies
    3
    Views
    908

    VXdiag Nano is J2534 cable that should work.

    VXdiag Nano is J2534 cable that should work.
  21. Replies
    170
    Views
    183,525

    Any news on nitrous patch ?

    Any news on nitrous patch ?
  22. Replies
    1,069
    Views
    685,112

    Ok thanks Best regards

    Ok thanks

    Best regards
  23. Replies
    1,069
    Views
    685,112

    Is there any chance by far to add slider for...

    Is there any chance by far to add slider for speedometer scalar so that it is easier to calibrate speedo. I do know there is a spreadsheet but I must be to dumb to use it cause every time I try it...
  24. Replies
    9
    Views
    1,571

    WB should be around 6-10" from collector and...

    WB should be around 6-10" from collector and before cats.
  25. Replies
    170
    Views
    183,525

    I have never played with Baro correction so can't...

    I have never played with Baro correction so can't help You here. But i have been at 100 feet and at around 2900 feet too and never needed to adjust anything in SD mode.
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4