that's really fresh oil, buddy. you must have pinched or damaged a gasket during installation, mistorqued something, missed some RTV'd corners that some GM gaskets require, or had mating surfaces...
Type: Posts; User: steveo
that's really fresh oil, buddy. you must have pinched or damaged a gasket during installation, mistorqued something, missed some RTV'd corners that some GM gaskets require, or had mating surfaces...
welcome. i know both mercruisers and the 7747 moderately well, maybe i can help. TBI with stern drives was a really short lived thing, yours was factory TBI?
most old 160 baud slow ass old tbi ECMs (which are probably older than the original nintendo entertainment system and have about the same processing power) have a newer 8192 baud cousin that is quite...
it's weird for sure. i have like 1/100 users eventually report weird interface issues. maybe it's just a crap interface with a counterfeit chip dying or bad wiring in the car. i would consider...
and you're sure the correct com port is selected?
with the old slow ECMS i had usually run open loop, disable AE, lock down timing outside of operating range, and just do my best. results have been really good and 'better than a carb n points' but...
if your IAC is too slow, throttle follower doesn't fix it or settings not available, and you want your idle to drop quickly, you can play with your timing advance vs idle error settings or whatever...
no it can't be an offset issue
whoever told you that you cant run whatever lobe sep or lift or whatever cam you want just can't tune worth a crap.
the challenge is with EFI you have a CONTROL LOOP. this could be fuel or idle...
as a general rule on any car if the log data is clean when engine is off, but becomes corrupt with engine on,
- try running with alternator disconnected. if situation improves, replace alternator...
of course i am a seasoned programmer with experience in ELM and 8192 baud ALDL protocol stuff, not sure what your skill level is
oh it's totally possible to make such a thing
i would use something like a raspberry pi and some off the shelf hardware to make it easy
the raspberry pi would run linux or whatever and would...
oh and just cause an ECM is refurbished doesn't mean it isn't junk....
ensure your grounds are okay by running a jumper from ECM case to vehicle chassis.
if that's no good maybe your burned bin is bad with an incorrect checksum, improperly offset, improperly inserted,...
many gm dual injector tbi systems have two modes, one where both injectors fire in a pattern left and right, and one where both fire together. there is usually an rpm threshold for this so at higher...
nothin?
come on guys you are so loyal and you send me tons of money but you can't do a few flash reads for me when you're out there tinkering? ;)
do send a datalog but you have replaced a lot of parts.
that is really damn frustrating
have reviewed your list of stuff you've done and determined that it's likely that one of your...
if your only goal is to delete the EGR, sending the chip to someone for a quicky EGR delete is definitely a good option
people on this forum tune themselves but for such a simple change that time...
these statements apply to any ecm not yours specifically
the iac doesn't have anything directly to do with idle mixture. it uses it to control idle speed instead of moving the throttle plate like...
usually obdxpro VT, what kind of car are you trying to tune?
hey all
i have recieved random reports about flash read not working in flashhack
thing is i dont have a test bench set up and am lazy and i dont remember what i've done to fix it
there is a...
with a speed density ecm you have a map that describes load vs rpm vs airflow for your particular engine
that changes when anything regarding airflow changes
that's definitely the first thing...
assuming you still have the original ECM for the truck?
a 1993 engine like that shouldn't have ever had a post cat o2 sensor so that's nothing to do with it
the lack of an EGR could cause a bit...
glad you beat it
its definitely something ive done before
no even a massive vac leak will not cause a fire. a fire in your throttle body could only be a severely leaking injector (unlikely) or a timing or valvetrain issue. is it possible that while...