Ok out comes the noob in me but I clicked on the thread to purchase the $45 shipped USB / ALDL cable that supports the forum etc. etc. Looks great, where can you actually purchase it? Is there a...
Type: Posts; User: Cricket_crawler
Ok out comes the noob in me but I clicked on the thread to purchase the $45 shipped USB / ALDL cable that supports the forum etc. etc. Looks great, where can you actually purchase it? Is there a...
I used the Binder Planet's step-by-step to do the conversion and built my own distributor.
The By-pass lies just outside the loom along the manifold by the TB. I did time with the bypass...
That is mostly out of necessity to keep it running especially when accelerating off idle! If I keep in drive I am setting myself up for the finger pointing and snickering from innocent passerbys!
$42 mask, ASDU bin, it is an automatic TF727.
Oh wow, I am sure I posted an old log :rolleye:...take a gander at this one!
IDK what a TCC is anyway, how would I disable this? Where can you find the error codes? what is code 24? I thought I was burning chips also, how would I get the spark advance or BPW into a log? ...
Sorry even though the status says fuel-injected we all know I am a noob...I hope you wanted the latest data log? I am attaching it anyway!!
Been trying to do some tuning, mostly to get rid of someof the hesitation and spit back. I have logged data and burned 4 differentchips with all but the same results, when I first fire up and get...
Good to know, I have mine running throught the floor via the transfer case shift lever boot. I can see it as I drive...proly not the safest thing but its temporary. Any ideas with my VSS?
I am running the 7747. While I have the pressure gauge hooked up, what is the optimum pressure to be at and what is the acceptable range for pressure drop? I will keep the gauge hooked up until I...
I have been working on tuning my IH Scout with an OBDI setup. I had a cheapy VSS and decided to up grade so I bought a Stewart Warner to match the SW speedo I found on ebay for $50, I picked up the...
Holy $&#! This is another point that reconfirms the fact that I am constantly over thinking things.
My logged BLM did not have any 100map so it zeroed out on the spreadsheet and VE table, will...
I fixed the temp sender and logged some data, terrible throttle response off of idle, popping back etc. Tunerpro locked up and I was unable to keep the initial data but did get 20 min worth of...
Will do...thank you
When building my Scout, I went with the serial data adapter to log data. After working with Tuner Pro and seeing how it works I would like to know if there is an easier way to get the data. Are...
Point well taken, I will chalk that down as another reason I am not running a knock...pretty sure when I had the exhaust installed it cleared the frame :mad1:, if its not one thing its another. ...
I have the O2 sensor mounted on the drivers side just downpipe from the manifold...pics attached.
I didn'e see your edit...I will make that sending unit a priority. I am thinking I had better get...
I uploaded the one (I believe) that you told me to load. I inserted it here just to be safe. Also, is it best to delete each of the data logging xdl files after the chip is burned? I am just...
I downloaded my Bin from this forum, under the 1227747 ECM Information $42 thread. I did keep an original, should I just reload that and start over? Or should I download it again from the site? ...
Ok, makes sense...I will take a look at getting that temp sender reinstalled. I guess now is when I get to learn how to tune, right. At what point do I enable the parameters that I disabled to log...
I have attached the pic of my sender...in looking at your suggestion I would say it could stay put?? Anyway, I am pretty jacked right now...burned my first chip put it in drove it logged more...
Any suggestions? Should I change the location of the sensor?
Yeah its an IH engine, I have the temp sender in the thermostat housing...
Now on to a total noob question...all the parameters I just changed, do I need to burn a chip and use that for the data...
Ok I found the spark advance hack as well as the BPW hack, when the dialog box opened I saved them?? Not sure if that is what I needed to do or was I to open the Hex editor and change the values...
I see the tables but am not sure how you apply them...or to turn things off for data logging. I am thinking I have the wrong temp sending unit in because my mechanical water temp was reading...