Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: myburb

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    362

    You have have some hardware and adapter and chip...

    You have have some hardware and adapter and chip to change and burn chips. The 329 is probably the apu1, I have that and it works well. It allows reading, writing, data logging and emulating and it...
  2. Replies
    10
    Views
    362

    Have you tried just data logging rather than...

    Have you tried just data logging rather than emulating. Some have found that easier to connect.
  3. Replies
    10
    Views
    362

    Try this...

    Try this
    http://www.gearhead-efi.com/Fuel-Injection/showthread.php?317-16147060-PCM-Information-85
    If this doesn't work goto the forum obd1 and then to definitions. To see real time you will need...
  4. Replies
    2
    Views
    194

    Help with ecm ident

    I am trying to help a friends son by telephone. He has a 95 s10, 4.3 vortec, standard trans. What mask do you think that would be running as a starting point for my looking.
  5. Thread: i'm an idiot

    by myburb
    Replies
    4
    Views
    198

    You have a start. You know .bin .xdf .adx which...

    You have a start. You know .bin .xdf .adx which are needed. Have you down loaded tuner pro rt? That would be a good step. Remember everyone had to start somewhere. lots of good help here. There...
  6. Replies
    26
    Views
    971

    Thanks for straightening that. As I typed was...

    Thanks for straightening that. As I typed was thinking of the old manual switching of both on for overdrive and then posted what I did. Must be age.
  7. Replies
    26
    Views
    971

    It has been along time since I did anything...

    It has been along time since I did anything inside a 4l80e but seem to remember the shift solenoids in the early ones and later (94-95) had different resistance solenoids. So the $31 and $OE might...
  8. Replies
    9
    Views
    561

    question for Fast355

    Not wanting to jack another thread you responded to, you talked about high cruise afrs in lean cruise with 7427. I have been able to manipulate my afrs to the way I want them but have only been able...
  9. Replies
    11
    Views
    615

    snowwebs, if you are interested you could send me...

    snowwebs, if you are interested you could send me a pm and I could load up your bin and maybe help you out. I only fool with big block chevs so don't often get to help out.
  10. Replies
    11
    Views
    615

    It has been my opinion to start with the bin and...

    It has been my opinion to start with the bin and mask that was originally with your transmission. Also I can't remember if the xdf for $31 has as many items as $OE. In my case I felt my 80e was...
  11. Replies
    11
    Views
    615

    ok I get you now. If you want to keep your $31...

    ok I get you now. If you want to keep your $31 that your truck came with download the files from the 6930 computer in the def area that you got the other xdf adx from.
  12. Replies
    11
    Views
    615

    If you want to use $OE use the xdf and adx that...

    If you want to use $OE use the xdf and adx that you find under the 6395 computer. 6395 and 7427 are interchangeable. You would need to use a $OE bin
  13. Replies
    36
    Views
    2,068

    In the beginning of my tune learning I chased...

    In the beginning of my tune learning I chased what I thought was a lean pop. After install WB realized it was not lean pop but anticipated spark retard. I lowered the amount of spark retard allowed...
  14. I think the moates hdr1 adapter might allow you...

    I think the moates hdr1 adapter might allow you to read the original without desoldering .
  15. Replies
    28
    Views
    1,043

    Tuned properly I was able to lower the idle rpm...

    Tuned properly I was able to lower the idle rpm by 125 and still be dead smooth. Going slowly around parking lots it is a stock feel. When you get on it there is a very noticeable difference to...
  16. Replies
    28
    Views
    1,043

    I have the same cam. As long as you leave the...

    I have the same cam. As long as you leave the stock injectors your stock bin will run it but not well. Because of the difference in vacuum it will probably run quite rich. I just used the apu1.
  17. Replies
    28
    Views
    1,043

    I have a 94 2500, mild modded 454, 4l80e. PCM is...

    I have a 94 2500, mild modded 454, 4l80e. PCM is 6395 and 7427, they both seem to work the same. If your motor is only minor modded l would just stick with the gm setup. I did a bunch of data...
  18. Replies
    18
    Views
    1,102

    I have had a goofy speedo for some time. It...

    I have had a goofy speedo for some time. It shifts fine, the speeds show correct in data log. I changed drac with no help, I changed instrument cluster with no help. Next time I have the cluster...
  19. Replies
    18
    Views
    1,102

    Regarding rich, any chance your reported water...

    Regarding rich, any chance your reported water temp is not going above your cold enrichment table and so always thinking it should have the (choke) on.
  20. Replies
    18
    Views
    1,102

    Re reading your post about tcc locking in 3rd, I...

    Re reading your post about tcc locking in 3rd, I don’t think I have seen any $OE that locks in 3rd. Years ago I did fool with using unused tow/haul numbers from $8D I think. I ended up just putting...
  21. Replies
    18
    Views
    1,102

    Just for clarity you do have the wire from the...

    Just for clarity you do have the wire from the tcc solenoid going to E11 so that the pcm grounds it, right
  22. Replies
    18
    Views
    1,102

    Have you modded any of the lock unlock speeds. ...

    Have you modded any of the lock unlock speeds. Years ago I was fooling with numbers and had that lock unlock problem. Turned out for me if you violate the spread/hysteriasis that can be a problem....
  23. Replies
    20
    Views
    1,506

    In the ve table you can modify the numbers any...

    In the ve table you can modify the numbers any way you want. In the function box you have multiply, divide,add, subtract, integer and maybe others so you are not limited to a mult of .6. What ever...
  24. Replies
    20
    Views
    1,506

    If I am reading the post correctly you haven’t...

    If I am reading the post correctly you haven’t tweaked the ve table down. If that is correct take idle table and lean it out. Try open and closed to see what you can come up with. Until your table...
  25. Thread: low BLM

    by myburb
    Replies
    48
    Views
    2,434

    I have found as long as you are looking for a...

    I have found as long as you are looking for a fuel pressure higher than your tbi spring, just connect return from tbi to inlet of aeromotive and outlet to return line, you are good to go.
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4