Search:

Type: Posts; User: f85gtron

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    5,865

    the site won't allow csv uploads. hmmm? ...

    the site won't allow csv uploads. hmmm?
    hopefully you can pull what you need from the log and other defs.
    Ron
  2. Replies
    7
    Views
    5,865

    Hi Dave, Here's the $A1 files and a log too, in...

    Hi Dave,
    Here's the $A1 files and a log too, in order to see how the idle works. $A1 seems to use both speed density and alpa-N both, blended at some point, but I can't figure out where. My...
  3. Replies
    7
    Views
    5,865

    Hi Dave, $A1 is the code mask I'm working with. ...

    Hi Dave,
    $A1 is the code mask I'm working with.
    Ron
  4. Replies
    7
    Views
    5,865

    need help creating idle history tables!!!

    I cannot figure out how to create idle blm history tables! Ultimately, I'd like to only use data when idle timer is activated and using idle ve table. is that possible? I can't figure out how to...
  5. Replies
    0
    Views
    2,674

    $88 launch mode. Can it two step?

    I noticed $88 launch control activates, but for partial throttle take-off, but I'd like to set it up for full pedal take-off, kind of like two-step, but mine is n/a. I've set the retard at like...
  6. thanks robert! i had them set to 0*. i thought...

    thanks robert!
    i had them set to 0*. i thought it would pull 0* timing out, not set to 0* on neg drpm! i found some 3.1 numbers from an auru bin and they work much better. ill play with it some...
  7. update: Ive got rdsc to work really well, with...

    update:
    Ive got rdsc to work really well, with the exception of decel. it cuts so much timing that the motor pops. it keeps pulling down past idle rpm almost to stall. with rdsc turned off,...
  8. Replies
    1
    Views
    3,572

    $14 ads adx needed

    I've acquired an 84 fiero and would like to read the aldl data. Apparently, 84s are different than the rest. Will a different ads work instead?Ecm 1226156
  9. Replies
    5
    Views
    5,170

    Pulse width is commanded, based off a calculation...

    Pulse width is commanded, based off a calculation of variables from several different inputs. If the pw is getting smaller while you rev, it's going opposite. Pw commanded has no correlation with...
  10. Replies
    5
    Views
    5,170

    I hear a lot of vacuum leak?. Maybe it's the...

    I hear a lot of vacuum leak?. Maybe it's the audio though. What happens when you rev it up?
  11. Replies
    4
    Views
    5,293

    nevermind. found it here. thanks again...

    nevermind. found it here. thanks again robert!http://www.gearhead-efi.com/Fuel-Injection/showthread.php?1928-16172693-16184164-16184737-16196397-PCM-Information-P66-V6
  12. Replies
    4
    Views
    5,293

    Thanks Robert,It's for an L32 motor. Is that...

    Thanks Robert,It's for an L32 motor. Is that still p66?
  13. Replies
    4
    Views
    5,293

    $2e 3.4 bin needed

    Does anyone have a $2e bin for a 93-95 camaro? I'm curious about the sa tables. I looked in the bin files, but couldn't find it.It's a 3.4
  14. Replies
    6
    Views
    5,733

    SOLUTION: It was the suspected cranking pw vs...

    SOLUTION:
    It was the suspected cranking pw vs coolant temp table. I reinstalled the 19# injectors and only changed the above mentioned table values to roughly 5 msec and VROOM! Cranked right up hot!...
  15. Replies
    6
    Views
    5,733

    Thanks to all who've helped. I think I've found...

    Thanks to all who've helped. I think I've found the problem, although I haven't been home to try the solution.
    Let me start by saying I'm an idiot :)
    I offset the values in the cranking pw vs...
  16. Replies
    6
    Views
    5,733

    Your probably right. However, I set the Multec...

    Your probably right.
    However, I set the Multec scaler and tables back to where they where before this condition and everything is normal, so it's one of those items for sure. Now that I'm thinking...
  17. Replies
    6
    Views
    5,733

    Can tuning overheat injector drivers?

    7730 using $88 mask.
    I've installed new injectors (Ford 302), changed bpw vs volts table and zeroed out bpw vs bpw table. I've also set the Multec fixing factor scaler to 0.
    Starts fine, runs...
  18. Replies
    8
    Views
    8,549

    I've used that max232 ttl board with both 160...

    I've used that max232 ttl board with both 160 (various fiero ecms) and 8192 baud (7730) ecms. Also used it with tuner pro and aldldroid.
    The chip comes mounted in a breakout board and all you...
  19. Replies
    8
    Views
    8,549

    Have you read this thread on the max232 chip?...

    Have you read this thread on the max232 chip? http://www.gearhead-efi.com/Fuel-Injection/showthread.php?719-Uber-easy-DIY-USB-ALDL-Cable&highlight=Max232
    I originally made a two transistor cable,...
  20. Replies
    13
    Views
    9,570

    My vote is for tuner pro. It's free and does...

    My vote is for tuner pro. It's free and does everything you'll need to do for now. Burning, reading, even emulating.
  21. Wow! Thanks for the explanation! I've already...

    Wow! Thanks for the explanation! I've already got the Speedo working from the ecm. It's just not "perfect", and that's what I'm looking for.....or less I wouldn't have gotten into tuning, right ;) ...
  22. If it helps, i made a buffer from the attached...

    If it helps, i made a buffer from the attached schematic. Could i simply add a pot to adjust something?
  23. Replies
    7
    Views
    5,443

    Welcome! The fiero is a great platform for swaps...

    Welcome! The fiero is a great platform for swaps and is very accommodating. I've swapped in the 3.4 from a camaro, an F23 trans from a cavalier, and ran it with a 7730 ecm. Both very good choices,...
  24. 7730 using $88 mask road speed constant to Speedo question

    I'm tuning a 24000 vss to a fiero. I'm running 14" tires and have had to adjust the road speed constant in $88 to about 26000 to calibrate to actual road speed. No problem there.
    The problem is:...
  25. Replies
    10
    Views
    9,811

    Ok. I'll watch it closely and check it against a...

    Ok. I'll watch it closely and check it against a timing gun. You guys are AWESOME!
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4