Search:

Type: Posts; User: greggbruceauto

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Hey thanks for this!! -- awesome bit of...

    Hey thanks for this!! -- awesome bit of information !!
  2. '93 4.3 Blazer CMFI replaced with 97 vortec 5.7 what's needed?

    I have searched for an hour now and not found any posts of anyone who has done something like this.

    Talking about the pcm, wiring and programming here. I have the engine, swap mounts and headers....
  3. Replies
    3
    Views
    5,684

    I guess I should check the trans position pid...

    I guess I should check the trans position pid next time I get to scan the car to see if it actually shows "drive" and "neutral" at the appropriate times.....
    thanks, I was looking for what I...
  4. Replies
    3
    Views
    5,684

    whatever is factory..... I don't see a parameter...

    whatever is factory..... I don't see a parameter with tunerpro that asks for neutral or drive.....

    not sure how to edit the xdf either.....

    unless you are asking about "IAC target speed...
  5. Replies
    73
    Views
    69,266

    um the t56 gears are at least as thick and...

    um the t56 gears are at least as thick and actually have more teeth, thus more tooth contact. compared to a m-20 or 21 or even a 22, they are more heavy duty..... the 4500's are cast iron, and have...
  6. Replies
    13
    Views
    16,555

    actually, if you lay the planets for both of...

    actually, if you lay the planets for both of those side by side, you will find that the 700/4l60 planets have physically bigger gears --- but the apply components for the 400/4l80 are bigger ----...
  7. Replies
    12
    Views
    18,319

    when I went to 4l60e school when I worked at the...

    when I went to 4l60e school when I worked at the dealer, they said it uses engine rpm, and has a "window" for the time it takes to complete a shift from the time it commands the solenoid to change...
  8. Replies
    3
    Views
    5,684

    305 TPI dies when put in gear

    305 mild cam, headers, 89 tpi firebird, $6E --- thought I had it fixed in warmer weather, but now it's cold out. When cold, starts and idles fine, as warms up, then if put in gear. will stumble and...
  9. if I remember correctly, this is close to what my...

    if I remember correctly, this is close to what my stock bin was set, just a few rpm below the cut-off, but (LOL) it was at something like 10,500....
    on the most recent bin I programmed, I set it to...
  10. Replies
    3
    Views
    4,752

    BLESS YOU !!! that was the explanation I was...

    BLESS YOU !!! that was the explanation I was looking for..... !!!!
  11. Replies
    3
    Views
    4,752

    confused about a TCC paramater

    1227165 ecm, $6e mask, 89 firebird TPI
    there are 4 tables in this bin
    TCC unlock speed vs. %TPS (not in 4th)
    TCC lock speed vs. % TPS (not in 4th)
    TCC unlock speed vs. % TPS (in 4th)
    TCC lock...
  12. yes, there are 2 parameters for each, disable and...

    yes, there are 2 parameters for each, disable and enable.

    I was just looking for people that have used these and what their experiences have been with them...
  13. well, let's say the kid is driving it at the...

    well, let's say the kid is driving it at the speed limiter say, 80 mph-- will that, if done for a long enough time, create an over lean situation that could hurt the engine?

    same thing with the...
  14. thoughts on rpm and speed limiters using fuel disable

    I am using 1227165 ecm with $6e mask (factory) with a modified chip for an 89 firebird 305 TPI.
    I have found the parameters in TunerproRT for disable and enable fuel, for both mph and rpm.
    I am...
  15. Replies
    26
    Views
    21,757

    yeah, I think I noticed that, every few seconds...

    yeah, I think I noticed that, every few seconds or so all the data would max/min out --- you can see it in graph mode....

    I just hope it's not going to be the case from now on...

    this car is...
  16. Replies
    26
    Views
    21,757

    sorry, it's a $6E, 1227165 89 F body TPI

    sorry, it's a $6E, 1227165 89 F body TPI
  17. Replies
    26
    Views
    21,757

    :rockon:A BIG thank you to ...

    :rockon:A BIG thank you to

    :jfj::jfj::jfj::jfj:
    for that link, I got it in the mail yesterday, and finally after figuring out the 12v cig lighter adapter on the cable has to be plugged in, and...
  18. Replies
    26
    Views
    21,757

    That's the direction I'm leaning towards now.....

    That's the direction I'm leaning towards now.....
  19. Replies
    26
    Views
    21,757

    yeah, asked him -- says he is waiting on parts

    yeah, asked him -- says he is waiting on parts
  20. Replies
    26
    Views
    21,757

    what is MAX 232 -- this is the first it has been...

    what is MAX 232 -- this is the first it has been brought up.... I thought you said 'FT232' -- how does that differ from RS232?
    I posted the links at the beginning of the thread -- the aldl cable I...
  21. Replies
    26
    Views
    21,757

    ummmmm, don't see any serial DB9 plugs on that...

    ummmmm, don't see any serial DB9 plugs on that page....
    and no, it doesn't have to be FTDI,

    IT JUST HAS TO BE SOMETHING THAT WORKS
  22. Replies
    26
    Views
    21,757

    yep, already did that -- found that post a week...

    yep, already did that -- found that post a week or so ago....
  23. Replies
    26
    Views
    21,757

    Yes, the cig lighter has good power and ground,...

    Yes, the cig lighter has good power and ground, it will run my snap on scanner and get data from the car just fine.

    yeah, windows recognizes the serial to usb 'bridge' it calls it. It changes com...
  24. Replies
    26
    Views
    21,757

    I guess my real dilemma :mad1: is whether or not...

    I guess my real dilemma :mad1: is whether or not to get another adapter
    http://www.mouser.com/ProductDetail/FTDI/CHIPI-X10/?qs=m5ogiX/X43nzRp8XLQeQIA==
    or...
  25. Replies
    26
    Views
    21,757

    so is that yes, or no?

    so is that yes, or no?
Results 1 to 25 of 33
Page 1 of 2 1 2