Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: Aksl

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. I'm trying to log the VE, Spark advance/retard,...

    I'm trying to log the VE, Spark advance/retard, stft, ltft.. I'm running rich, have bad startup and no cold idling (where the truck runs at higher rpm until warms up a little), can't start not...
  2. Hi everyone, well unfortunately i,m totaly stuck...

    Hi everyone, well unfortunately i,m totaly stuck with my project. I have downloaded a few programs for logging, tried to log and record it, did alot ot reading, and from what i understood is that i...
  3. Hello Fast355, if you have a minute to help me...

    Hello Fast355, if you have a minute to help me setup scanxl config or share your knowledge on pid's you use to config map tables in order to see and analyze what changes to make to the tune file, i...
  4. Hello Fast355, sorry for bothering, i wonder,...

    Hello Fast355, sorry for bothering, i wonder, could you please share your ScanXL config file please?

    With set up (configured) tables and graphics that you use..

    Sincerely.
  5. Hey evryone, So, I have been dancing with the...

    Hey evryone,

    So, I have been dancing with the tambourine around my truck today, and found a few problems that I had, due to which I got OBD2 with scanXL not connecting to the interface and ECM....
  6. Ok, if no other advice, i will be dancing with...

    Ok, if no other advice, i will be dancing with the tambourine around my truck this weekend, will report on the results...
  7. I doubt it, checked the calibration, the error on...

    I doubt it, checked the calibration, the error on VATS is turned off, i attach the screen shot and my calibration file.
  8. Ok, thank you! will try to adjust the fueling...

    Ok, thank you! will try to adjust the fueling this way and then just plug back in the MAF.
  9. Hello NISANDA, ok i see, will try to next time i...

    Hello NISANDA, ok i see, will try to next time i go deal with my truck, yesterday i couldn't even got it started to move it, if before it would start with pedal aplied and i could move it, then...
  10. Ok so today i went and tried again with different...

    Ok so today i went and tried again with different calibrations to give it a try, since my battery was all charged. Well with a lot of tries i killed the battery again, couldn’t get it to start and...
  11. I have saved the both calibrations in PDF and...

    I have saved the both calibrations in PDF and transformed to Exel sheet, made comaparison as pdf files, and manualy whent through all of the tables transfered to excel files and copied out the...
  12. Thank you Fast355, since i can not do a...

    Thank you Fast355, since i can not do a comparison in TunerCat, but hopefully TunerCat let`s you print data to .txt or via printer settings to .pdf and compare it, i will compare all tables between...
  13. Hello everyone, so i have been to my track today,...

    Hello everyone, so i have been to my track today, unfortunately it is parked a bit away from my home, and is parked outside. So it is a bit challenging to work on it every time, not always I’m able...
  14. I will be going to my truck today, will try to...

    I will be going to my truck today, will try to upload the newly made .cal files i have, and will report up on the result tonight. It`s -20șC today, but with pedal applied by ± 20% the truck starts no...
  15. What cables are you guys using for data logging,...

    What cables are you guys using for data logging, is there any special feature, or chip, or is it just with support for "J1850 VPW" standard and thats all? :popcorn:
  16. Hello NISANDA, it is nice to hear from you again,...

    Hello NISANDA, it is nice to hear from you again, thank you for the .cal file you have provided me earlier, and great thank you for the update, really appreciate!
    I will compare the files today, to...
  17. Hello PlayingWithTBI, " I don't want to step on...

    Hello PlayingWithTBI, " I don't want to step on this thread, maybe I should start a new one?" - As you wish, but personaly i don`t mind you using this my thread, as long as it give you help & result!...
  18. I see, i will consider it, will watch some...

    I see, i will consider it, will watch some youtube and read about it, thank you, may be I will just buy that. As i understood, i can simply use an ELM327 ODB II wire with it? Is that so?

    I prefer...
  19. Well, thats a hell of a list of engine gens..., i...

    Well, thats a hell of a list of engine gens..., i have only downloaded & uploaded calibration files to cars like smart fortwo brabus calibration, WV Tiguan, TLC200, Nissan NP300, and a few more, and...
  20. Missed out your question, for data logging i`m...

    Missed out your question, for data logging i`m using chineese Tech II, but thinking of going to ELM 327 USB addapter with ScanMaster ELM 2.1 software...

    Becouse i can not write a file with the...
  21. Wow 16 years experience, i gues i`m very lucky...

    Wow 16 years experience, i gues i`m very lucky that you have run in to my thread. It is really good and right thing to share your knowledge, personaly i do as well share my experiance with everyone,...
  22. Concerning Crank VE, i have this file downloaded...

    Concerning Crank VE, i have this file downloaded from HPtunner forum, that converts the VE to crank VE, may be you will find it usefull..
  23. Thank you very much Fast355, appreciate your help...

    Thank you very much Fast355, appreciate your help and guidance!

    Sincerely!
  24. Ow, ok, thank you for corrections, i will swap...

    Ow, ok, thank you for corrections, i will swap the values in IDLE RPM table with AC on/of for P/N to In gear and vice versa, thank you!

    Trying to convert right now the % values to gm/cyl/sec for...
  25. Ow, and the values in the BIG CAM EXCEL file...

    Ow, and the values in the BIG CAM EXCEL file provided by Fast355 are in %, and i just copied them, now have to convert to gm/cyl/sec and update the values. Thanks for noticing that Mitch!
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4