Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: mihela

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: ALDLdroid

    by mihela
    Replies
    1,100
    Views
    415,716

    Thanks for the reply! I knew they were still...

    Thanks for the reply! I knew they were still there, but that folder is pretty deep in there and I never would have known to look there.
  2. Thread: ALDLdroid

    by mihela
    Replies
    1,100
    Views
    415,716

    After one of the recent updates I can't figure...

    After one of the recent updates I can't figure out where the logs are being saved on my phone. They used to be in the ALDL folder. I've had to email them to myself and that's irritating. Normally I...
  3. Replies
    6
    Views
    448

    I imagine that's a difficult PCM to find stuff...

    I imagine that's a difficult PCM to find stuff for. 1 year only for only the Cutlass Supreme and Monte Carlo Z34 if I remember my W-bodies.
  4. Replies
    7
    Views
    556

    I never did change mine because of this exact...

    I never did change mine because of this exact issue. I don't have a clue as to how to correlate the tables from $42 to usec values.
  5. My 95 4WD trans has the output reluctor.

    My 95 4WD trans has the output reluctor.
  6. Replies
    33
    Views
    18,725

    I have been playing around with the Efan control...

    I have been playing around with the Efan control in my truck and decided to take a crack at adding the $0E fan hack right into the XDF file. This XDF also has the fan parameters added as scalars if...
  7. Replies
    5
    Views
    460

    Just an update, The Spartan has a feature where...

    Just an update, The Spartan has a feature where it sends a voltage value of 1.66 then 3.33 volts on startup. I did a very short datalog and the AFR value is correct with the equation as is.
  8. Replies
    5
    Views
    460

    The quality of the part is outstanding. Shipping...

    The quality of the part is outstanding. Shipping was very slow however and the website flagged my debit card when I tried to order. It sounds like its a small operation however and they are very...
  9. Replies
    5
    Views
    460

    I must not have searched for the right thing....

    I must not have searched for the right thing. That thread was very helpful.
  10. Replies
    5
    Views
    460

    WB02 calibration in adx file?

    I just purchased and installed a Spartan 2 WB02. Previously I was use an AEM UEGO that I was borrowing from a friend. I am not sure how the AFR value is actually calculated for logging in the ADX? I...
  11. Replies
    1
    Views
    384

    Good stuff in here. I have a 20 ton HF press and...

    Good stuff in here.
    I have a 20 ton HF press and if you have a local scrap metal place that sells offcuts you can do like I did and get a bunch of round off cuts to use as press adapters. Our place...
  12. Replies
    12
    Views
    1,471

    Both sensors are the same! AC Delco 21392, GM...

    Both sensors are the same! AC Delco 21392, GM 10456549. I checked that before I quit working at Chevy, and RockAuto is the same.
  13. Replies
    12
    Views
    1,471

    I have been using that spreadsheet, it a great...

    I have been using that spreadsheet, it a great tool. I use an AEM wideband fed in through the EGR position wire.
  14. Replies
    12
    Views
    1,471

    My distributor at this point is functionally...

    My distributor at this point is functionally identical to a 368 distributor. I could use a 368 distributor if I wanted to find one. I have full computer controlled timing. As far as the knock sensors...
  15. Replies
    12
    Views
    1,471

    Here's a few more. I am using a 350 knock sensor...

    Here's a few more. I am using a 350 knock sensor and it works fine, as some of my early tunes indicated. :innocent2:
  16. Replies
    12
    Views
    1,471

    I am using an 8625 with $0E based on BHDF...

    I am using an 8625 with $0E based on BHDF already, based on your recommendation. It works pretty well.
  17. Replies
    12
    Views
    1,471

    Sanity Check Cadillac 500 Tune

    I've been working on my 1995 Cadillac powered Chevy for a while and got most of the bugs worked out. I was hoping to get some feedback to see if I've made in egregious errors or if I'm on the right...
  18. Replies
    14
    Views
    2,048

    It is entirely possible to exceed MBT on good...

    It is entirely possible to exceed MBT on good combustion chambers. Higher is not always better.
  19. Replies
    8
    Views
    1,455

    The 16196396 is a kind of oddball. It is an older...

    The 16196396 is a kind of oddball. It is an older style ECM with 160 baud communication and no all in one memcal. You need the CABL1 combo instead.
  20. Just a note for any new people who stumble onto...

    Just a note for any new people who stumble onto this thread, make sure you set up the values in your datastream definition to also take into account you initial advance otherwise your data logs and...
  21. Thread: segment gauge

    by mihela
    Replies
    11
    Views
    2,644

    Sounds promising. Having cheap microcontrollers...

    Sounds promising. Having cheap microcontrollers available for general purpose use has made so many things possible. I plan turning one into a trip computer for the roof console in my truck and...
  22. Replies
    3
    Views
    1,032

    I'm sure they would require the correct...

    I'm sure they would require the correct datastream and likely E&C bus data to function, and changing that would require extensive reverse engineering of the software inside the unit. I bet they can...
  23. Replies
    2
    Views
    696

    The Crossfire is a great story of typical GM...

    The Crossfire is a great story of typical GM "what might have been". It has a lot of potential in it and was a great concept just factory choked. I look forward to reading about your progress.
  24. $0E Main spark tables and their relationship to initial advance

    I'm in the process of tuning my Cadillac motor running an '6395 with a BHDF base and $0E. In the spark timing tables are the numbers actual timing or are they added to initial timing? I already am...
  25. Replies
    11
    Views
    1,676

    I realized I actually have the early 90lb...

    I realized I actually have the early 90lb injectors, so when I set it to 80 is was too rich. I need to change out the oil/filter and then I can run it again and set up the idle and start logging some...
Results 1 to 25 of 34
Page 1 of 2 1 2