Search:

Type: Posts; User: WallyCJ7

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: Search issue

    by WallyCJ7
    Replies
    1
    Views
    4,603

    Search issue

    For some reason I get no results when I search with the keyword MSD. I know there are posts that have MSD in them since I posted one myself.
    ...
  2. Replies
    5
    Views
    5,411

    I have an MSD distributor and that just what MSD...

    I have an MSD distributor and that just what MSD calls it. I thought I was connecting it just as the MSD installation guide shows I think...
  3. Replies
    5
    Views
    5,411

    Here the issue I’m having, during cranking the...

    Here the issue I’m having, during cranking the injectors are not firing. If I disconnect the magnetic pickup connector to the MDS box and the injector fire during engine cranking. I can then...
  4. Replies
    5
    Views
    5,411

    Yes I got it used. Thanks

    Yes I got it used.

    Thanks
  5. Replies
    5
    Views
    5,411

    MSD 6L installation help

    What I’m looking to do is install a MSD 6L ignition box. I know there has to be posts on this but the search doesn’t find anything. Strange

    What I’m looking for is the info that tells me if I...
  6. Thread: New Jeep guy

    by WallyCJ7
    Replies
    5
    Views
    5,673

    Yes I'm in San Diego county

    Yes I'm in San Diego county
  7. Thread: New Jeep guy

    by WallyCJ7
    Replies
    5
    Views
    5,673

    There's a couple of jeep guys hanging out here......

    There's a couple of jeep guys hanging out here... I have a 78 with a 401.
  8. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    I found the problem. I took the chips to the...

    I found the problem. I took the chips to the local Dyno shop and they have a burn2. He tried to load my BIN file and has the same results on both chips.
    He pulled out one of his chips and the BIN...
  9. Never mind, found one...

    Never mind, found one...
  10. Help Needed - Anyone here in San Diego County?

    I'm having issues flashing my chip and I'm looking for someone close that I can test flash a chip so I know for sure it's my burner or the chips.

    Thanks

    Wally
  11. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    No luck side to side... I moved it like 5 times.

    No luck side to side... I moved it like 5 times.
  12. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    Yes 4k and I've tried 256k too

    Yes 4k and I've tried 256k too
  13. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    Are you saying side to side or a different set of...

    Are you saying side to side or a different set of slots? I'll try side to side.
  14. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    Notch towards the arm and set furthest away from...

    Notch towards the arm and set furthest away from the arm
  15. Thread: Burn1 issue

    by WallyCJ7
    Replies
    9
    Views
    10,363

    Burn1 issue

    Today I trying to work on tuning and I'm thinking the Burn1 is not working.

    Start Flash & Burn

    27SF512 highlighted
    Chip address set to Start: 00F000 End: 00FFFF
    Buffer address: start 000000...
  16. Replies
    33
    Views
    24,724

    I now have the avatar working and here's another...

    I now have the avatar working and here's another shot of mine. It a 78 CJ7 401. T400. Atlas 5:1, Dana 60 4:56's F&R, Detroit in the rear and a ARB in front, Hydro boost brake and hydro assist...
  17. Replies
    33
    Views
    24,724

    Yes I could smell that it was rich with out the...

    Yes I could smell that it was rich with out the computer. But it wasn't spitting and popping going down the road.
    I have the spreadsheet from Eaglemark and I've added a sheet to track the changes...
  18. Replies
    33
    Views
    24,724

    I finally got a good working ECM - thanks Brian...

    I finally got a good working ECM - thanks Brian and I went back and tried the .BIN file you adjusted. After a rough startup and after warning up I was able to take it out for some data collecting...
  19. Replies
    5
    Views
    5,371

    I understand PCM baud rate but why the memcal out...

    I understand PCM baud rate but why the memcal out of a 7.4L over the 5.7L?
    I have the G1 with the ZIF socket ordered so I should be good to go...
  20. Replies
    5
    Views
    5,371

    Scored a 7427 BPRK from a 454BBC today.

    You got to love a 1/2 price sale at the junk yard today:rockon:. The 2nd truck I checked already had the glove box removed and I didn't even need any tools to pull it out. I now have the wires to...
  21. Replies
    2
    Views
    4,739

    Moates G1 adapter?

    Do you need a Moates G1 adaptor to use a 27SF512 chip in a 16197429 PCU?

    Can the Eprom be pulled and the 27SF512 chip be installed?
  22. Replies
    8
    Views
    8,286

    Thanks guys I may take you up on your offer. I...

    Thanks guys I may take you up on your offer. I find that one pin may not be soldering for some reason - probably dirty. I thought I cleaned everything really good. Now I need to find out how to...
  23. Replies
    8
    Views
    8,286

    Its a nice older Weller power base and stand, but...

    Its a nice older Weller power base and stand, but its non adjustable so I cant tell what wattage it's running.
    I went by radio shack and picked up some flux core solder and some de-soldering...
  24. Replies
    8
    Views
    8,286

    $42 soldering for a 27SF512 socket

    During my attempt at trying to tune my system I started getting communication errors with the laptop. I was thinking it was too high baud rate so I lowered it to 4800 and it still had errors and...
  25. Replies
    33
    Views
    24,724

    I used asdu9567.bin. Was that the stock one?

    I used asdu9567.bin. Was that the stock one?
Results 1 to 25 of 44
Page 1 of 2 1 2