....
Printable View
....
....
....
....
Thank You!
Thank you!!! Also would it be possible to get these XDFs complied into a ZIP file?
*Edit* Would these XDFs work with a 4896 ECU? Its pretty much the same as a 0411
Thank you for all the work you've put into these, I know how much time they take to create.
I can't wait to see where this leads us now that open source flashing is now possible.
Nice work on the XDFs but it'd be nice if you had contacted me before you included versions of my checksum plugins, and provided creditation for my work. Also, you should NOT load both checksums. The 1 Mbyte should be an update to the 512kb, and carries the same internal GUID as the earlier version which needs to be unique. In fact, I think tunerpro will detect this and ignore the older one and use the 1 Mbyte plugin for all. Also grrr at whoever patched out my email address from the DLLs! :( Im not saying its you but it definately has happened. Thats nasty. I'd like to clean that up.
For the checksum plugins to work you'll need the VC2010 redist package installed on your PC else it'll fail to load, and then it wont update the checksums which will cause problems flashing. Also note that you only need the plugin for the OS Segments, and unless you have code patches (I dont think anyone has developed any yet) you can and should use the built in tunerpro checksum calculations instead as that will remove the external dependency on the checksum plugin and in turn the VC2010 plugins so that it will always work.
I'll attach my build of the 512kbyte and 1mbyte plugin. If you want to talk plugin development send me a PM.
Here is an example of checksum without a plugin for the engine calibration segment, the same applies for all segments except the OS segment:
....
....
No, this is the first public release of the 1mbyte version, though its just a minor update. I can see that the 1mbyte dll you posted is someone elses hack of my dll as there is an extra space where someone typed over the 512kbit string.
The source code for the guts of it is published here but I cant post in full because of the restrictive license on the tunerpro SDK.Code:This plug-in provides a way to calculate checksums for LS1 512k bin files.
This plug-in provides a way to calculate checksums for LS1 1Mb bin files.
https://pcmhacking.net/forums/viewto...&t=3845#p85328
The offical 1Mbyte support is added by duplicating the if which sets os_hack=1 and updating the end address for the extra bin range.
Can you please update you zip with the plugin I posted above and remove the stolen copies?Code:// if we detect its the LS1 OS range, then enable a hack to skip parts that are not included
if (pCalcInfo->dwRegionStartAddress==0 && pCalcInfo->dwRegionEndAddress==0x7FFFD) os_hack=1;
if (pCalcInfo->dwRegionStartAddress==0 && pCalcInfo->dwRegionEndAddress==0xFFFFD) os_hack=1;
If you need more proof see the filesystem string in the dlls from my server where oseplugin is mentioned, which is a completely unrelated plugin for older delco pcms on pcmhacking.net. Thats in all versions....
LRT, you have done great work, and I understand the confusion, this hacked version has been passed around and I have just been informed someone is or was selling an ls1 flash tool on ebay, and they removed the credits and included it in the package they are selling. So that is the source of the hacked version. It is deliberately stolen work, but not by anyone here. I am happy for the real version to be passed around and I have shared how it works for the community and I have shared my ls1flash-free source and kernel with NSFW and open sourced a lot of my former work in PCM Hammer but I have a problem with this plugin. I dont think its fair to strike my name out of it. Please dont distribute the hacked version. Since we are all a community (or a couple of communities) working towards the same goal, you are welcome to distribute the one I posted above.
Now I understand whats going on, and I see how the 2 bytes of guid were hacked. The 2 stolen copies can load side by side because of the differing IDs, and they hacked the DLL twice because they couldnt add the one line of code that was needed. So they just changed 7FFFD to FFFFD in the second copy. To be very clear I am only talking about the checksum dlls, not the rest of LRTs work which is fantastic and a huge needed piece of the free flashing solution.
Attachment 13633
Wow i can see this is going to be ugly in some areas. Not sure why someone would want jack with the checksum and repost it. I know i had messaged Antus awhile back pcmhacking about a 1mb checksum and he offered to to make one. And furthermore anyone thats been involved with this project its common knowledge who made them. People are going to mess up a good thing.I can see xdfs going the same way.
....
....
I can do that - I would be happy to fix them up and send them back if your open to that. I think 1 plugin is better than 2 or more (if or when we develop more stuff in the future). Otherwise I'd need to use the same GUIDs at the hacked one too, which I guess is possible but I'd rather not base my work on the direction the hack was going. Contact me by PM and we can decide and do something out of this thread.
LRT, did you also make the custom operating systems? Where can we get the bin files for those?
Thanks for all of your hard work!
NSFW, LRT, PeteS, antus and EVERYONE else who is working to make this happen in any capacity...... Thank you all! You guys embody the spirit of hot-rodding by making this accessible to everyone.
Hi guys - I`m cross posting from the corvette forum here.
I ordered the AllPro USB ELM327 adaptor and have been able to read my BIN file successfully, 01Z06 with mods and a tune. Great! I think, going via the other thread that I can also write the cal changes I want, even better.
However the final piece needed is data logging. Can anyone help? I found a few LS1 tagged ADX files but none of them get anything in TunerPro from my car.
I set tunerpro to use plug-in, set plug-in to ELM327OBDII interface.
1 of the ADX files lets me connect ok but rate is ~1Hz and i'm not getting any channels coming back. 2 of the ADX files let me connect but with rolling errors and no data. The other files don't even get me connected....
The built in plugin, as far as i can tell doesnt do anything. I use scalxl pro at this stage as ive had a license for it for years. But I do have a working elm327 adx, but a quick test this morning shows it needs some fixes to work on the allpro. If you want to help and understand the elm protocol and adx authorship i'll send it, else give me a few days and i'll see if i can get it going and release it.
Hi LRT thanks for the amazing work. My question is, as I am trying to enable data tracing using tuner pro, are your xdf files already set up to work with an adx file? I only ask as the guide I have tried to use mentions having to edit the xdf to suit the tracing and yours are password protected so don't allow the option to do so. Or if I am barking up the wrong tree just go ahead and slap me down. I am a noob to all this tuning stuff. Cheers.
anyone have tips on what i need to change to run a manual trans on my 99 lm7 ecu
WOW!!! WOW!! WOW!!! To all of the gentlemen that have worked so hard to make this a reality, my hat is off to you all. well done!! I just gotta get it setup lol. I have been using EFILive for a few years now, still have mixed feelings about it. I do own a licensed version of Tuner Pro RT just hadn't worked with it much, I guess it's time to get into it shoulder deep.
Thanks again for the work past, present, and future.
Hi i'm new here, first of all thanks LRT for the great work, second does anyone has a 9381344 OS XDF File? I've find only one for a F body and i'm not sure it'll work in my 4.8 out of a 2000 Silverado that i'm currently swapping into my 77 2WD K5 Blazer
Did you ever get an XDF file to work with your 09354896 ECU?
No, i updated my pcm to an OS with an available xdf file and now all is working fine
Hi Im quite new to this thread and forum. Im having problems Downloading the attached files.
I got the TunerPro editing software - for LS1 type PCMs.pdf and printed it.
Im having trouble with PCM OS Checksum Plugins.zip as when I click the link and select save as it goes to save a attachment.php then Im not able to open it.
Am I doing something wrong?
I believe that someone said IE does that if you're not using "compatibility mode." You can right click, "save as," then type in the file name you want.
Hi Guys, I have managed to the the Bin file from my PCM a OS 12212156 which came with the LS 6.0 Engine I got from a scrap yard.
I also got the .xdf file for the 2002 GM Vehicle in this thread.
The original transmission is showing as a 4L80E but I want to use my 700R4 as this has very recently been fully rebuilt.
The 6.0 LS will be going into my 1989 GMC Vandura G2500 Van.
Am I able to just change to transmission type and then save or is it more complicated? to I need to change other settings aswell.
I need to delete VATS
EGR
Cooling fans
Probably the Speedometer section with wheel size etc.
Maybe the 02 Sensors aswell. (still reading up on whats needed).
Many thanks.
I'm glad you've figured a way around the issue. When you "Save As" the browser suggests a filename. You can change the name of the file by typing in the name manually.
Unfortunately I can't get screenshots at this time as my browser saves the files with the correct names.
Thanks I'll give that a try aswell.
I am not finding .xdf files for 2000 LS1 cars.
I have a 2000 Camaro M6 that is using the OS 9381344.
Can anyone help or point me in the right direction?
I've had my computer mail order tuned way back when I was first working on my build and was hoping to just tweak the "Safe" tune. It is very rich and has some idle issues with the A/C on. If I update the OS and flash a new .bin, I'll be back to square one... Correct?