Connecting WB O2 to 1227727 ECU

Hi all!
I just downloaded TunerPro RT V5, so I can log WB O2 data. I am using 8D_SAUJP_V4a.xdf.
I have been searching here, Corvette forum, and Thirdgen for my answer...no joy.
I would like to know what pin (1227727 ECU) should I connect my Innovate LC-1 (0-5v) output to, and any steps needed in TPRTV5 to accomplish my goal.

The only info I found was a recommendation to use pin C-21, but no one has a step by step tutorial for this process, even the Innovate web site has nothing.
Another question I have is if the ECU pin out showed that a pin was not used, how can I know that the internal circuitry will accept the WB data, and most importantly, be able to record that data in the ALDL stream?
Thanks!

Maybe the attached .zip folder will help?

dave w

Thanks!
Wow fast response! I seem to always loose the instruction manual. I think is gets thrown out with the wrapping paper, or maybe I over estimate my ability to figure things out. I hope my wife never sees this.:innocent2:

Is the pin F14 in the 7730 ECU the same as C21 in the 1227727 ECU?
Just trying to confirm the proper location to attach the LC-1(0-5v) output.
Also the proper WB flag to set is not clear. It should read WB, OPT1, b5 = Innovate LC1 (0-5v) not(1-2v). Is this a typo, or does the output need to be reprogrammed, or use a different flag like WB OPT 2,b0 = RAW A/D Output

https://pcmhacking.net/ludis/p4xref.html#1227727

https://pcmhacking.net/ludis/quadplugecm.html

dave w

Thanks Dave,
If I read the schematics properly then C21 pin in the 7727 ECU is the same as F14 in the 7730.
I still am not sure about which flag to set in the code patch, due to the voltage range listed for the Innovate LC-1 controller.
Shouldn't the range be more like (0-5v), rather than (1-2v)?
What am I missing?
.

.

Narrow band O2 sensors are 0v - 1v. Wide Band O2 is 0v - 5v.

I've only set up the 16197427 PCM's for WBO2.

I don't have experience setting up the 1227727 for WBO2.

dave w

I appreciate your help! I may have an answer in the TGO stickies section. "WB on Super AUJP"

Quote:

---

Originally Posted by Dr.E

Hi all!
I just downloaded TunerPro RT V5, so I can log WB O2 data. I am using 8D_SAUJP_V4a.xdf.
I have been searching here, Corvette forum, and Thirdgen for my answer...no joy.
I would like to know what pin (1227727 ECU) should I connect my Innovate LC-1 (0-5v) output to, and any steps needed in TPRTV5 to accomplish my goal.

The only info I found was a recommendation to use pin C-21, but no one has a step by step tutorial for this process, even the Innovate web site has nothing.
Another question I have is if the ECU pin out showed that a pin was not used, how can I know that the internal circuitry will accept the WB data, and most importantly, be able to record that data in the ALDL stream?
Thanks!

---

Look at this thread as it should help you get the wideband connected and working correctly. I used this info when I installed a wideband o2. C 21 is the correct pin to use with the 1227727 ECU. I will look further for more information on this install. I thought there was a tutorial but can't find it.

Thanks,Eds! Now I feel better about the proper pin to use. I am still searching archives for Tunerpre RT v5 and 8D_SAUJP_4a to determine which is the proper flag to set and which value to select in Tunerpro.

I think this is what I need to do: https://www.thirdgen.org/forums/dfi-...0-wideband.htm
Set flag WB OPT 2, bit 0, RAW A/D Output and select in Tunerpro RT v5 , WB AFR (LC-1 0-5v) in the ADX Editor.
The confusing part is that there is also a WB AFR (Raw Data) value in the ADX Editor, but I think that is for other WB's with a different voltage range.
Any comments on my logic?...Reality check?
Thanks again all!

Don't know why but the link did not work for me.

This one?https://www.thirdgen.org/forums/dfi-...-wideband.html