How can I convert a tun to a bin.?
Printable View
How can I convert a tun to a bin.?
Post your .tun and I will give it a try.
Jeff
Here is it
It figures. You post a 1mb tune that I don't have the stuff with me to do it today. I will have to do it in the morning. If it was a 512kb, I could do it now.
Jeff
No problem Jeff. Give it a try in the morning.
Here is the .tun file you provided converted to .bin
Jeff
You posted 512KB my original file is 1Mb
Sorry about that. I had my software set to only read out 512kb of info---My Mistake.
Here is your .tun converted to .bin.
Jeff
Thank you Jeff.
May I ask you what software did you use to convert 1MB?
I flashed your .tun into a licensed 1mb PCM and read it out as .bin in Tunercat. I didn't have the software set properly in Tunercat the first time.
Jeff
Hello Good Day My Dear
please can you convert tis file to bin
information : engine LS1 5.7 V8 4l60e
Here is it
Attachment 10710
Thank you Jeff.
There are two 2002 Express van bins here:
http://www.gearhead-efi.com/Fuel-Inj...ll=1#post18585
One is a 4L60, the other is a 4L80.
thank you LRT for quick answer but all of that is coded by tunerpro software
and Mr dave w you are right
I want that file for ls1 pcm and i found bin file for ls1 and i programed directly to the chip but engine does not run
my problem is VATS ,Car starts and immediately dies
I have raw bin file and I don't have hptuners and efilive interface , i cant buy that
If i have another way to disable that security system please tell me
I thinking i need raw bin file that VAT was disabled
I transplants engine and now does not run
If you can please help me:rolleye:
here is my pcm file
Attachment 10713
Many Thanks
The tune that you attached to post #13 is corrupt, as is the bin that you attached to post #16.
I would not recommend using either of these.
What are you using to flash the PCM ?
What exact engine and transmission combination do you have ?
Better to answer these questions first, and then perhaps we can find a way to provide help that is actually useful.
The attached .bin is not Stock, use at your own RISK! I can't remember all the changes I did, but I'm sure I disabled VATS. Basically I flashed a PCM with the modified Corvette .ctz file I downloaded from Tune Depot. Then I read back the modified Corvette flash as a .bin file.
dave w
Thank you for posting the photos ... in this case a picture is indeed worth 1000 words !
The engine is a 24x CKP and 1x CMP (Gen 3), so the Express Van tune (4x CKP and 1x CMP) from post #13 will not operate this engine.
Whatever software you are using to read directly from the flash chip, is saving the raw data (bin file) in a unique order, which is not readily compatible with tuning software. This is why the bin in post #16 appeared to be corrupt. It is not corrupt, but rather just saved in a unique format.
You can only flash a bin file with your software, that uses this specific format. Do NOT flash any bins found on the internet using this software - the result would likely be catastrophic to the PCM.
Now that I know how your bin data is saved, I can work with this format.
What do you need ?
VATS turned off ?
Rear oxygen sensors turned off ?
Transmission mounted Gear Position Switch deleted ?
Just let me know ....
thank you for your information about ls1 and l31
software that i used to read chip is a programmer software . I can read,write,erase,and save file with that. image1
1-yes just i want disable VATS (turned off)
2-this engine doesn't have any oxygen sensor ( no oxygen sensor-first and rear sensor)even all the pins related to the sensor is empty in pcm and doesn't have MAF sensor
3-yes the Transmission mounted Gear Position Switch (selector or pnp) is removed image2
thank you
Wow ...
OK, I took a look at your calibration, and it is indeed setup to operate in Open Loop all of the time. The short-term and long-term fuel trims are disabled, and all four oxygen sensors have been disabled.
This type of tune is not recommended for anything other than a dedicated race or competition vehicle. At minimum you will want to permanently install a wide band oxygen sensor, to monitor your air / fuel ratio.
Attached below is the bin that you posted, with the VATS disabled and the transmission mounted Gear Position (or PNP) Switch disabled.
Use this bin at your own risk. It is based on a 2001 Holden with an LS1 and a 4L60E.
thank you so much
I appreciate
I will test this file
Any chance the original is for leaded fuel?
Binary data storage / priority uses different forms. Your software appears to store the bin in Little Endian format. I first converted your bin to Big Endian format (which most tuning software will recognize, and open), then I edited this reformatted bin using Tunerpro. Once the editing was complete, I converted the format back to Little Endian, so that you could flash it.
I looked up the user manual for your software. If you go to the Buffer Menu, it appears you can switch between Little Endian and Big Endian format using the "swap bytes" option.
LS1 engine run video
https://www.4shared.com/video/pSePeV..._17-02-25.html
do you have special XDF file (tunerpro)?
I can't find xdf file for this type of pcm
VATS turned off ?
Rear oxygen sensors turned off ?
Transmission mounted Gear Position Switch deleted ?
Could I have a copy of that attachment lrt. Thanks
It has been a long time since that project. This forum brought up so many good memories for me. thanks to LRT (http://www.gearhead-efi.com/Fuel-Inj...r.php?4905-LRT)
I'm glad now I can continue the cycle of helping others.
Here you are: https://drive.google.com/file/d/1H-r...ew?usp=sharing
VATS and Gear Position Service has been disabled.
No oxygen sensor at all.
The file has been uploaded on my drive, so hopefully, it will be available forever for anyone.