branpowell606
05-11-2022, 11:18 PM
I have read a bunch of posts looking for this info while trying to find it myself. I'll post up what I have, because I couldn't find it either and had to make it. I just got done swapping a 0411 PCM into my 99 OBS 5.7 L31 Suburban 4x4 with 4l60e with A/C, and Pushbutton 4x4. Everything works so far, throttle response is way better, driving is smoother, and 0-60 times is much faster. Special Thanks to Lextech for the ideas and first write-up on gmtruckcentral.com and to Brendan from lt1swap.com for the info he has up. I referenced his how-to, but did not use his pinout. He seemed to be inactive for a while, so I decided to figure it out on my own. I will give you guys all I have with the reference websites I used as well for someone else interested in this swap. The wiring for 98-99 OBS Suburbans, Tahoes, Yukons, Sierras, Silverados with a 5.7L 4l60e etc should all be the same, I believe 96-67 will have differences. Not sure what they are, but I have another project with a 96 Tahoe, so I'll find out at some point. Obviously, there will also be differences for Manual trans, or any other applications.
My Tune: 12212156 OS, o2 Express Van, 02 s10 4l60e 4x4 Trans segment swapped in, Cyl Vol increased to 723cc\cyl for .020 bore, VATS disabled, EVAP DTCs disabled, O2 downstream codes deleted, EGR disabled, Trans abuse protection enabled, Fan #1 Turn on 205\off 200, I do NOT have the Fan #2 relay control enabled in my tune. (DTC Disable list: 0137, 0138, 0140, 0141, 0157, 0158, 0160, 0161, 0401, 0404, 0405, 0420, 0430, 0440, 0442, 0443, 0446, 0449, 0452, 0453, 0461, 0462, 0463.)
Stock Tune: 12212156 OS, 02 Express Van, 02 s10 4l60e 4x4 Trans segment swapped in, VATS disabled, Trans abuse protection disabled(stock), all other options left alone.
For wiring, I followed along on Lextech's article. Don't forget to add in the Trans wires for the Range switch(AKA PRND Input)!! You have to splice into these from the transmission plug or behind the gauge cluster. I chose the gauge cluster just so my wiring was further from dirt and water. The pics are missing from Lextechs post for the guage cluster connecter, but the wire colors are Blk/Wht, Grey, Yellow, and White. There are only four wires on that connector that color and beside each other, so it's hard to miss them. You will have to add in a few wires to the PCM for these four, so it's good to have the wires from the depinned blue/red 0411 connector handy. You will also have to splice some wires together to add in PCM grounds and such. In my wiring pinout, I added in Wires for Fan #1 Relay control, Tow mode button(momentary to ground), Rear knock sensor, and dual fuel tanks(OEM type) for future planned mods. lt1swap.com has the pinout marked for the 0411 PCM if you want to run it stand-alone or without EVAP. I included all wires, including A/C, just because mine still has it for the time being.
I marked all splices in the sheet with Black boxed outlines, but I will write them out just in case.
99 Blackbox Conn and Pin-------------- 02 0411
Clear C3 Pin 4 ------ Blue Pin 54, Blue Pin 63, Blue Pin 41
Clear C3 Pin 17 ------ Blue Pin 1, Blue Pin 40
Clear C3 Pin 18 ------ Red Pin 1, Red Pin 40
Clear C3 Pin 19 ------ Red Pin 57, Blue Pin 60, Blue Pin 23, Blue Pin 53
Clear C3 Pin 21 ------ Blue Pin 20, Blue Pin 57
Black C4 Pin 3, Black C4 Pin 4 ------ Red Pin 50
Lextech's write up: www.gmtruckcentral.com/articles/12200411.html (http://www.gmtruckcentral.com/articles/12200411.html)
0411 02 Express pinout: https://lt1swap.com/99-02_vortec_pcm.htm
0411 Wiring Schematics/Harness: https://lt1swap.com/gen3_schematics.htm
96-99 Vortec Blackbox Pinouts: https://lt1swap.com/96-99_vortec_harness.htm
96-99 Vortec Schematics/Harness: https://lt1swap.com/96-99_vortec_harness.htm
Attached is the Pinout pdf.
My Tune: 12212156 OS, o2 Express Van, 02 s10 4l60e 4x4 Trans segment swapped in, Cyl Vol increased to 723cc\cyl for .020 bore, VATS disabled, EVAP DTCs disabled, O2 downstream codes deleted, EGR disabled, Trans abuse protection enabled, Fan #1 Turn on 205\off 200, I do NOT have the Fan #2 relay control enabled in my tune. (DTC Disable list: 0137, 0138, 0140, 0141, 0157, 0158, 0160, 0161, 0401, 0404, 0405, 0420, 0430, 0440, 0442, 0443, 0446, 0449, 0452, 0453, 0461, 0462, 0463.)
Stock Tune: 12212156 OS, 02 Express Van, 02 s10 4l60e 4x4 Trans segment swapped in, VATS disabled, Trans abuse protection disabled(stock), all other options left alone.
For wiring, I followed along on Lextech's article. Don't forget to add in the Trans wires for the Range switch(AKA PRND Input)!! You have to splice into these from the transmission plug or behind the gauge cluster. I chose the gauge cluster just so my wiring was further from dirt and water. The pics are missing from Lextechs post for the guage cluster connecter, but the wire colors are Blk/Wht, Grey, Yellow, and White. There are only four wires on that connector that color and beside each other, so it's hard to miss them. You will have to add in a few wires to the PCM for these four, so it's good to have the wires from the depinned blue/red 0411 connector handy. You will also have to splice some wires together to add in PCM grounds and such. In my wiring pinout, I added in Wires for Fan #1 Relay control, Tow mode button(momentary to ground), Rear knock sensor, and dual fuel tanks(OEM type) for future planned mods. lt1swap.com has the pinout marked for the 0411 PCM if you want to run it stand-alone or without EVAP. I included all wires, including A/C, just because mine still has it for the time being.
I marked all splices in the sheet with Black boxed outlines, but I will write them out just in case.
99 Blackbox Conn and Pin-------------- 02 0411
Clear C3 Pin 4 ------ Blue Pin 54, Blue Pin 63, Blue Pin 41
Clear C3 Pin 17 ------ Blue Pin 1, Blue Pin 40
Clear C3 Pin 18 ------ Red Pin 1, Red Pin 40
Clear C3 Pin 19 ------ Red Pin 57, Blue Pin 60, Blue Pin 23, Blue Pin 53
Clear C3 Pin 21 ------ Blue Pin 20, Blue Pin 57
Black C4 Pin 3, Black C4 Pin 4 ------ Red Pin 50
Lextech's write up: www.gmtruckcentral.com/articles/12200411.html (http://www.gmtruckcentral.com/articles/12200411.html)
0411 02 Express pinout: https://lt1swap.com/99-02_vortec_pcm.htm
0411 Wiring Schematics/Harness: https://lt1swap.com/gen3_schematics.htm
96-99 Vortec Blackbox Pinouts: https://lt1swap.com/96-99_vortec_harness.htm
96-99 Vortec Schematics/Harness: https://lt1swap.com/96-99_vortec_harness.htm
Attached is the Pinout pdf.