Activity Stream

Welcome! I just to live in Syracuse, loved going to junkyards (with a sawzall)! Be sure to update your location in your profile so we know where...

I did opt for the G1 adapter, thanks!

Thanks for this. I guess I was wrong - the decel surge is still there although it seems to be a little softer. Now I'm wondering if there is an IAC...

Thanks so much for your help. I wont be with the truck or burner untill sunday. Untill then I'll try and do some more research. Knowing how, will...

If Decel surge continues, try reducing spark advance by 2-3 degrees in the cells affected by decel.

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?7736-New-to-Forum-and-Tuning-Can-t-seem-to-find-correct-BIN&p=74168&viewfull=1#post74168

Welcome to the forum. There's plenty of good information here if you look around.

So I've been having trouble getting my 1993 (8625) S10 with a 4.3 to run properly now that I've swapped a manual trans from a 92 into it. I got...

You might consider a G1 adapter unless you plan on desoldering the original PROM and installing a zif... http://support.moates.net/g1/

I placed my order for the APU1. I think I'll be happiest with what that method. Excellent input, guys! Thanks!

For the 16197427, the bare bones tuning kit requires a chip programmer ( the chip is actually a 27C512), UV Eraser (to erase the original memcal...

Thank you very much, thats what I needed to know on the fan wiring. Was expecting a whole different relay setup. :yikes: As for the fueling, I...

yeah, with that Volvo setup the temp sensor grounds the pin to the relays the same way the 7427 pcm would. So you can swap over one of the wires from...

Depending on application EBL comes with a lot of starter tunes- so you aren't starting from scratch, Rob is a great resource. On the minus at least...

I had one installed semi permenantely as well on my old G20. I have the first generation APU1. Needed a replacement Datalog cable and Craig was...

I've had an APU1 hooked up to my G20 van for ages, eventually I'll replace it with a chip. I've just changed my cam so it's just easier to upload...

Then I think that's the route I will take. The APU1 package. steveo, I appreciate you looking out for may wallet! All in all, it's not a huge extra...

I do not own, or have I ever used the APU1. I own and regularly use both the Ostrich 2.0 and Burn 2. For tuning the 16197427, I regularly use a...

No IAT in $0E or $0D unless modified.

Tuned properly I was able to lower the idle rpm by 125 and still be dead smooth. Going slowly around parking lots it is a stock feel. When you get...

Excellent. I appreciate the input. Is it fairly user-friendly?

Fair enough. I guess I'm just curious. Plus, I may want to put it to use in the future. I've had many OBD1 cars, mostly TBI, and will likely have...

I have the same cam. As long as you leave the stock injectors your stock bin will run it but not well. Because of the difference in vacuum it will...

emulators are cool but this is a pretty mild build. why not just install a zif, get a few chips and a programmer? that's how most old gm ecms are...

Yessir, at the very least I believe I am. Of all the tests runs I've done for fueling, I've never seen "tcc applied" but noticed "tcc energized" all...

Ok, cool. Makes sense. Those are currently backordered on Moates.net. Since I have none of this equipment, the APU1 kit seems to be an all-in-one...

After "Tuning" is complete, there are two options: 1. Keep the Ostrich 2.0 installed. 2. Remove the Ostrich 2.0 and installed a chip programmed...

I was never able to get the p/n working on a 7427. All of my swaps show in drive always except for the ones where i swapped in a 4l60e as well. And...